ath79: add support for Ubiquiti PowerBeam 5AC Gen2

The Ubiquiti PowerBeam 5AC Gen 2 (PBE-5AC-Gen2) is an outdoor 802.11ac
5 GHz bridge with a radio feed and a dish antenna. The device is
hardware-compatible with the LiteBeam AC Gen2, plus the 4 extra LEDs.

Specifications:
 - SoC: Qualcomm Atheros AR9342 rev 2
 - RAM: 64 MB DDR2
 - Flash: 16 MB SPI NOR (mx25l12805d)
 - Ethernet: 1x 10/100/1000 Mbps Atheros 8035, 24 Vdc PoE-in
 - WiFi 5 GHz: QCA988x HW2.0 Ubiquiti target 0x4100016c chip_id 0x043222ff
 - WiFi 2.4 GHz: Atheros AR9340 (SoC-based)
 - Buttons: 1x (reset)
 - LEDs: 1x power, 1x Ethernet, 4x RSSI via GPIO. All blue.
 - UART: not tested

Installation from stock airOS firmware:
 - Follow instructions for WA-type Ubiquiti devices on OpenWrt wiki

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[changed device name in commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit is contained in:
Roger Pueyo Centelles 2020-03-12 11:37:10 +01:00 committed by Adrian Schmutzler
parent f0435d5343
commit e210fe91b1
5 changed files with 80 additions and 2 deletions

View File

@ -0,0 +1,66 @@
// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "ar9342_ubnt_wa.dtsi"
/ {
compatible = "ubnt,powerbeam-5ac-gen2", "ubnt,wa", "qca,ar9342";
model = "Ubiquiti PowerBeam 5AC Gen2";
aliases {
led-boot = &led_rssi3;
led-failsafe = &led_rssi3;
led-upgrade = &led_rssi3;
};
leds {
compatible = "gpio-leds";
rssi0 {
label = "ubnt:blue:rssi0";
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
};
rssi1 {
label = "ubnt:blue:rssi1";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
rssi2 {
label = "ubnt:blue:rssi2";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
};
led_rssi3: rssi3 {
label = "ubnt:blue:rssi3";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
};
};
};
&mdio0 {
status = "okay";
phy-mask = <4>;
phy4: ethernet-phy@4 {
reg = <4>;
};
};
&eth0 {
status = "okay";
/* default for ar934x, except for 1000M and 10M */
pll-data = <0x02000000 0x00000101 0x00001313>;
mtd-mac-address = <&art 0x0>;
phy-mode = "rgmii-id";
phy-handle = <&phy4>;
gmac-config {
device = <&gmac>;
rxd-delay = <3>;
rxdv-delay = <3>;
};
};

View File

@ -282,7 +282,8 @@ ubnt,rocket-m)
ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "ubnt:green:link4" "wlan0" "76" "100"
;;
ubnt,nanobeam-ac|\
ubnt,nanostation-ac)
ubnt,nanostation-ac|\
ubnt,powerbeam-5ac-gen2)
ucidef_set_rssimon "wlan0" "200000" "1"
ucidef_set_led_rssi "rssilow" "RSSILOW" "ubnt:blue:rssi0" "wlan0" "1" "100"
ucidef_set_led_rssi "rssimediumlow" "RSSIMEDIUMLOW" "ubnt:blue:rssi1" "wlan0" "26" "100"

View File

@ -53,6 +53,7 @@ ath79_setup_interfaces()
ubnt,nanostation-loco-m|\
ubnt,nanostation-loco-m-xw|\
ubnt,picostation-m|\
ubnt,powerbeam-5ac-gen2|\
ubnt,rocket-m|\
ubnt,unifiac-lite|\
ubnt,unifiac-lr|\
@ -468,7 +469,8 @@ ath79_setup_macs()
ubnt,unifi)
label_mac=$(cat /sys/class/ieee80211/phy0/macaddress)
;;
ubnt,litebeam-ac-gen2)
ubnt,litebeam-ac-gen2|\
ubnt,powerbeam-5ac-gen2)
label_mac=$(mtd_get_mac_binary art 0x5006)
;;
ubnt,routerstation|\

View File

@ -25,6 +25,7 @@ case "$FIRMWARE" in
ubnt,nanobeam-ac|\
ubnt,nanostation-ac|\
ubnt,nanostation-ac-loco|\
ubnt,powerbeam-5ac-gen2|\
ubnt,unifiac-pro|\
yuncore,a770)
caldata_extract "art" 0x5000 0x844

View File

@ -243,6 +243,14 @@ define Device/ubnt_picostation-m
endef
TARGET_DEVICES += ubnt_picostation-m
define Device/ubnt_powerbeam-5ac-gen2
$(Device/ubnt-wa)
DEVICE_MODEL := PowerBeam 5AC
DEVICE_VARIANT := Gen2
DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct rssileds
endef
TARGET_DEVICES += ubnt_powerbeam-5ac-gen2
define Device/ubnt_rocket-m
$(Device/ubnt-xm)
SOC := ar7241