ath79: add support for D-Link DAP-2695-A1
Hardware: * SoC: Qualcomm Atheros QCA9558 * RAM: 256MB * Flash: 16MB SPI NOR * Ethernet: 2x 10/100/1000 (1x 802.3at PoE-PD) * WiFi 2.4GHz: Qualcomm Atheros QCA9558 * WiFi 5GHz: Qualcomm Ahteros QCA9880-2R4E * LEDS: 1x 5GHz, 1x 2.4GHz, 1x LAN1(POE), 1x LAN2, 1x POWER * Buttons: 1x RESET * UART: 1x RJ45 RS-232 Console port Installation via stock firmware: * Install the factory image via the stock firmware web interface Installation via bootloader Emergency Web Server: * Connect your PC to the LAN1(PoE) port * Configure your PC with IP address 192.168.0.90 * Open a serial console to the Console port (115200,8n1) * Press "q" within 2s when "press 'q' to stop autoboot" appears * Open http://192.168.0.50 in a browser * Upload either the factory or the sysupgrade image * Once you see "write image into flash...OK,dest addr=0x9f070000" you can power-cycle the device. Ignore "checksum bad" messages. Setting the MAC addresses for the ethernet interfaces via /etc/board.d/02_network adds the following snippets to /etc/config/network: config device 'lan_eth0_1_dev' option name 'eth0.1' option macaddr 'xx:xx:xx:xx:xx:xx' config device 'wan_eth1_2_dev' option name 'eth1.2' option macaddr 'xx:xx:xx:xx:xx:xx' This would result in the proper MAC addresses being set for the VLAN subinterfaces, but the parent interfaces would still have a random MAC address. Using untagged VLANs could solve this, but would still leave those extra snippets in /etc/config/network, and then the device VLAN setup would differ from the one used in ar71xx. Therefore, the MAC addresses of the ethernet interfaces are being set via preinit instead. The bdcfg partition contains 4 MAC address labels: - lanmac - wanmac - wlanmac - wlanmac_a The first 3 all contain the same MAC address, which is also the one on the label. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit is contained in:
Stijn Tintel
parent
7e287ff89d
commit
cd09f26660
176
target/linux/ath79/dts/qca9558_dlink_dap-2695-a1.dts
Normal file
176
target/linux/ath79/dts/qca9558_dlink_dap-2695-a1.dts
Normal file
@ -0,0 +1,176 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "qca955x.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "dlink,dap-2695-a1", "qca,qca9558";
|
||||
model = "D-link DAP-2695-A1";
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200n8";
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power_red;
|
||||
led-failsafe = &led_power_red;
|
||||
led-running = &led_power_green;
|
||||
led-upgrade = &led_power_red;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power_green: power_green {
|
||||
label = "d-link:green:power";
|
||||
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
led_power_red: power_red {
|
||||
label = "d-link:red:power";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wifi2g {
|
||||
label = "d-link:green:wifi2g";
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "mx25l12805d";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "bdcfg";
|
||||
reg = <0x040000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "rgdb";
|
||||
reg = <0x050000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "langpack";
|
||||
reg = <0x060000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@70000 {
|
||||
compatible = "wrg";
|
||||
label = "firmware";
|
||||
reg = <0x070000 0xf00000>;
|
||||
};
|
||||
|
||||
partition@f70000 {
|
||||
label = "captival";
|
||||
reg = <0xf70000 0x070000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@fe0000 {
|
||||
label = "certificate";
|
||||
reg = <0xfe0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@ff0000 {
|
||||
label = "art";
|
||||
reg = <0xff0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
|
||||
qca,ar8327-initvals = <
|
||||
0x04 0x07600000 /* PORT0_PAD_CTRL */
|
||||
0x0c 0x00080080 /* PORT6_PAD_CTRL */
|
||||
0x7c 0x0000007e /* PORT0_STATUS */
|
||||
0x94 0x0000007e /* PORT6_STATUS */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
phy-handle = <&phy0>;
|
||||
phy-mode = "rgmii";
|
||||
pll-data = <0x56000000 0x00000101 0x00001616>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
ð1 {
|
||||
status = "okay";
|
||||
|
||||
phy-mask = <0>;
|
||||
phy-mode = "sgmii";
|
||||
pll-data = <0x03000101 0x00000101 0x00001616>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
qca,no-eeprom;
|
||||
};
|
||||
@ -136,6 +136,9 @@ ath79_setup_interfaces()
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "2:wan" "3:lan" "4:lan"
|
||||
;;
|
||||
dlink,dap-2695-a1)
|
||||
ucidef_add_switch "switch0" "0@eth0" "2:lan" "3:wan" "6@eth1"
|
||||
;;
|
||||
dlink,dir-825-b1)
|
||||
ucidef_set_interface_wan "eth1"
|
||||
ucidef_add_switch "switch0" \
|
||||
@ -361,6 +364,9 @@ ath79_setup_macs()
|
||||
devolo,magic-2-wifi)
|
||||
label_mac=$(macaddr_add "$(mtd_get_mac_binary art 0x1002)" 3)
|
||||
;;
|
||||
dlink,dap-2695-a1)
|
||||
label_mac=$(mtd_get_mac_ascii bdcfg "wlanmac")
|
||||
;;
|
||||
dlink,dir-825-b1)
|
||||
lan_mac=$(mtd_get_mac_text "caldata" 0xffa0)
|
||||
wan_mac=$(mtd_get_mac_text "caldata" 0xffb4)
|
||||
|
||||
@ -14,6 +14,10 @@ case "$FIRMWARE" in
|
||||
avm,fritz450e)
|
||||
caldata_extract_reverse "urlader" 0x1541 0x440
|
||||
;;
|
||||
dlink,dap-2695-a1)
|
||||
caldata_extract "art" 0x1000 0x440
|
||||
ath9k_patch_mac $(mtd_get_mac_ascii bdcfg "wlanmac")
|
||||
;;
|
||||
dlink,dir-505|\
|
||||
dlink,dir-825-c1|\
|
||||
dlink,dir-835-a1)
|
||||
|
||||
@ -40,6 +40,10 @@ case "$FIRMWARE" in
|
||||
caldata_extract "art" 0x5000 0x844
|
||||
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) -1)
|
||||
;;
|
||||
dlink,dap-2695-a1)
|
||||
caldata_extract "art" 0x5000 0x844
|
||||
ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac_a)
|
||||
;;
|
||||
dlink,dir-859-a1)
|
||||
caldata_extract "art" 0x5000 0x844
|
||||
ath10k_patch_mac $(mtd_get_mac_ascii devdata "wlan5mac")
|
||||
|
||||
@ -6,9 +6,17 @@ fix_seama_header() {
|
||||
[ "$kernel_size" ] && mtd -c 0x$kernel_size fixseama firmware
|
||||
}
|
||||
|
||||
fixwrgg() {
|
||||
local kernel_size=$(sed -n 's/mtd[0-9]*: \([0-9a-f]*\).*"kernel".*/\1/p' /proc/mtd)
|
||||
[ "$kernel_size" ] && mtd -c 0x$kernel_size fixwrgg firmware
|
||||
}
|
||||
|
||||
board=$(board_name)
|
||||
|
||||
case "$board" in
|
||||
dlink,dap-2695-a1)
|
||||
fixwrgg
|
||||
;;
|
||||
qihoo,c301)
|
||||
fix_seama_header
|
||||
;;
|
||||
|
||||
@ -8,6 +8,10 @@ preinit_set_mac_address() {
|
||||
avm,fritz450e)
|
||||
ip link set dev eth0 address $(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))
|
||||
;;
|
||||
dlink,dap-2695-a1)
|
||||
ip link set dev eth0 address $(mtd_get_mac_ascii bdcfg "lanmac")
|
||||
ip link set dev eth1 address $(mtd_get_mac_ascii bdcfg "wanmac")
|
||||
;;
|
||||
enterasys,ws-ap3705i)
|
||||
ip link set dev eth0 address $(mtd_get_mac_ascii u-boot-env0 ethaddr)
|
||||
;;
|
||||
|
||||
@ -6,6 +6,7 @@ include ./common-yuncore.mk
|
||||
DEVICE_VARS += ADDPATTERN_ID ADDPATTERN_VERSION
|
||||
DEVICE_VARS += SEAMA_SIGNATURE SEAMA_MTDBLOCK
|
||||
DEVICE_VARS += KERNEL_INITRAMFS_PREFIX
|
||||
DEVICE_VARS += DAP_SIGNATURE
|
||||
|
||||
define Build/add-elecom-factory-initramfs
|
||||
$(eval edimax_model=$(word 1,$(1)))
|
||||
@ -49,6 +50,14 @@ define Build/cybertan-trx
|
||||
-rm $@-empty.bin
|
||||
endef
|
||||
|
||||
define Build/mkwrggimg
|
||||
$(STAGING_DIR_HOST)/bin/mkwrggimg -b \
|
||||
-i $@ -o $@.imghdr -d /dev/mtdblock/1 \
|
||||
-m $(DEVICE_MODEL)-$(DEVICE_VARIANT) -s $(DAP_SIGNATURE) \
|
||||
-v $(VERSION_DIST) -B $(REVISION)
|
||||
mv $@.imghdr $@
|
||||
endef
|
||||
|
||||
define Build/nec-enc
|
||||
$(STAGING_DIR_HOST)/bin/nec-enc \
|
||||
-i $@ -o $@.new -k $(1)
|
||||
@ -88,6 +97,10 @@ define Build/teltonika-fw-fake-checksum
|
||||
dd of=$@ bs=1 count=16 seek=$$offs conv=notrunc
|
||||
endef
|
||||
|
||||
define Build/wrgg-pad-rootfs
|
||||
$(STAGING_DIR_HOST)/bin/padjffs2 $(IMAGE_ROOTFS) -c 64 >>$@
|
||||
endef
|
||||
|
||||
define Device/seama
|
||||
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
|
||||
KERNEL_INITRAMFS := $$(KERNEL) | seama
|
||||
@ -458,6 +471,26 @@ define Device/devolo_magic-2-wifi
|
||||
endef
|
||||
TARGET_DEVICES += devolo_magic-2-wifi
|
||||
|
||||
define Device/dlink_dap-2695-a1
|
||||
SOC := qca9558
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
|
||||
DEVICE_VENDOR := D-Link
|
||||
DEVICE_MODEL := DAP-2965
|
||||
DEVICE_VARIANT := A1
|
||||
IMAGES := factory.img sysupgrade.bin
|
||||
IMAGE_SIZE := 15360k
|
||||
IMAGE/default := append-kernel | pad-offset 65536 160
|
||||
IMAGE/factory.img := $$(IMAGE/default) | append-rootfs | wrgg-pad-rootfs | \
|
||||
mkwrggimg | check-size
|
||||
IMAGE/sysupgrade.bin := $$(IMAGE/default) | mkwrggimg | append-rootfs | \
|
||||
wrgg-pad-rootfs | append-metadata | check-size
|
||||
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
|
||||
KERNEL_INITRAMFS := $$(KERNEL) | mkwrggimg
|
||||
DAP_SIGNATURE := wapac02_dkbs_dap2695
|
||||
SUPPORTED_DEVICES += dap-2695-a1
|
||||
endef
|
||||
TARGET_DEVICES += dlink_dap-2695-a1
|
||||
|
||||
define Device/dlink_dir-505
|
||||
SOC := ar9330
|
||||
DEVICE_VENDOR := D-Link
|
||||
|
||||
Loading…
Reference in New Issue
Block a user