ramips: Add support for the GnuBee Personal Cloud Two
The GnuBee Personal Cloud Two crowdfunded on https://www.crowdsupply.com It is a low-cost, low-power, network-attached storage device. Specifications: - SoC: MediaTek MT7621AT - RAM: DDR3 512 MB - Flash: 32 MB - Six SATA ports for 3.5" Drives - One SDcard - One USB 3.0 - Two USB 2.0 - Gigabit Ethernet: Three Ports - UART 3.5mm Audio Jack or 3 pin header - 57600 8N1 - Three GPIOs available on a pin header Flash instructions: The GnuBee Personal Cloud Two ships with libreCMC installed. libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt. As such one can upgrade using the webinterface or sysupgrade. Das U-Boot has multiple options for recovery or updates including : - USB - http - tftp Errata: - While there are three ethernet ports, the third requires support for the second GMAC. This will come in kernel 4.14. - The first hard drive slot has a clearance issue with the two fan headers. Workaround is to pull the headers out and connect the pins to jumper wires. - Using this device as a NAS is problematic with the 4.9 kernel as many /dev/sdX reads throw silent errors. The current theory behind this is some kind of unhandled DMA mapping error in the kernel. This is not an issue with kernel 4.4. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> Signed-off-by: Rosen Penev <rosenp@gmail.com>
This commit is contained in:
Rosen Penev
John Crispin
parent
2d27ebbb93
commit
c60a21532b
@ -191,6 +191,12 @@ gb-pc1)
|
||||
ucidef_set_led_switch "lan1" "lan1" "$boardname:green:lan1" "switch0" "0x01"
|
||||
ucidef_set_led_switch "lan2" "lan2" "$boardname:green:lan2" "switch0" "0x10"
|
||||
;;
|
||||
gb-pc2)
|
||||
ucidef_set_led_switch "lan" "lan" "$board:green:lan" "switch0" "0x01"
|
||||
ucidef_set_led_switch "wan" "wan" "$board:green:wan" "switch0" "0x10"
|
||||
ucidef_set_led_netdev "eth1-g" "eth1-g" "$board:green:eth1-g" "eth1"
|
||||
ucidef_set_led_netdev "eth1-y" "eth1-y" "$board:green:eth1-y" "eth1"
|
||||
;;
|
||||
gl-mt300a|\
|
||||
gl-mt300n|\
|
||||
gl-mt750)
|
||||
|
||||
@ -206,6 +206,10 @@ ramips_setup_interfaces()
|
||||
ucidef_add_switch "switch0" \
|
||||
"0:lan" "4:lan" "6@eth0"
|
||||
;;
|
||||
gb-pc2)
|
||||
ucidef_add_switch "switch0" \
|
||||
"4:lan" "0:wan" "6@eth0"
|
||||
;;
|
||||
gl-mt300n-v2)
|
||||
ucidef_add_switch "switch0" \
|
||||
"1:lan" "0:wan" "6@eth0"
|
||||
|
||||
@ -91,6 +91,7 @@ get_status_led() {
|
||||
dir-620-d1|\
|
||||
dwr-512-b|\
|
||||
gb-pc1|\
|
||||
gb-pc2|\
|
||||
hpm|\
|
||||
hw550-3g|\
|
||||
mac1200rv2|\
|
||||
|
||||
@ -205,6 +205,9 @@ ramips_board_detect() {
|
||||
*"GB-PC1")
|
||||
name="gb-pc1"
|
||||
;;
|
||||
*"GB-PC2")
|
||||
name="gb-pc2"
|
||||
;;
|
||||
*"GL-MT300A")
|
||||
name="gl-mt300a"
|
||||
;;
|
||||
|
||||
@ -61,6 +61,7 @@ platform_check_image() {
|
||||
fonera20n|\
|
||||
freestation5|\
|
||||
gb-pc1|\
|
||||
gb-pc2|\
|
||||
gl-mt300a|\
|
||||
gl-mt300n|\
|
||||
gl-mt750|\
|
||||
|
||||
137
target/linux/ramips/dts/GB-PC2.dts
Normal file
137
target/linux/ramips/dts/GB-PC2.dts
Normal file
@ -0,0 +1,137 @@
|
||||
/dts-v1/;
|
||||
|
||||
#include "mt7621.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
compatible = "gnubee,gb-pc2", "mediatek,mt7621-soc";
|
||||
model = "GB-PC2";
|
||||
|
||||
memory@0 {
|
||||
device_type = "memory";
|
||||
reg = <0x0 0x1c000000>, <0x20000000 0x4000000>;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,57600";
|
||||
};
|
||||
|
||||
palmbus: palmbus@1E000000 {
|
||||
i2c@900 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys-polled {
|
||||
compatible = "gpio-keys-polled";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
poll-interval = <20>;
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
system {
|
||||
label = "gb-pc2:green:system";
|
||||
gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
status {
|
||||
label = "gb-pc2:green:status";
|
||||
gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
lan {
|
||||
label = "gb-pc2:green:lan";
|
||||
gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wan {
|
||||
label = "gb-pc2:green:wan";
|
||||
gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
eth1-y {
|
||||
label = "gb-pc2:yellow:eth1-y";
|
||||
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
eth1-g {
|
||||
label = "gb-pc2:green:eth1-g";
|
||||
gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
};
|
||||
};
|
||||
|
||||
&sdhci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
m25p80@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <10000000>;
|
||||
m25p,chunked-io = <32>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x30000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x30000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
factory: partition@40000 {
|
||||
label = "factory";
|
||||
reg = <0x40000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "firmware";
|
||||
reg = <0x50000 0x1fb0000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&cpuclock {
|
||||
compatible = "fixed-clock";
|
||||
clock-frequency = <900000000>;
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ðernet {
|
||||
mtd-mac-address = <&factory 0xe000>;
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
state_default: pinctrl0 {
|
||||
gpio {
|
||||
ralink,group = "uart3";
|
||||
ralink,function = "gpio";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -83,6 +83,14 @@ define Device/gb-pc1
|
||||
endef
|
||||
TARGET_DEVICES += gb-pc1
|
||||
|
||||
define Device/gb-pc2
|
||||
DTS := GB-PC2
|
||||
DEVICE_TITLE := GnuBee Personal Cloud Two
|
||||
DEVICE_PACKAGES := kmod-ata-core kmod-ata-ahci kmod-usb3 kmod-sdhci-mt7620
|
||||
IMAGE_SIZE := $(ralink_default_fw_size_32M)
|
||||
endef
|
||||
TARGET_DEVICES += gb-pc2
|
||||
|
||||
define Device/hc5962
|
||||
DTS := HC5962
|
||||
BLOCKSIZE := 128k
|
||||
|
||||
Loading…
Reference in New Issue
Block a user