ath79: add support for NEC Aterm WG800HP
NEC Aterm WG800HP is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9563. Specification: - Qualcomm Atheros QCA9563 - 64 MB of RAM (DDR2) - 8 MB of Flash (SPI-NOR) - 2.4/5 GHz wifi - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 1T1R (QCA9887) - 4x 10/100/1000 Mbps Ethernet - 8x LEDs, 3x keys (2x buttons, 1x slide-switch) - UART through-hole on PCB (J2) - Vcc, GND, NC, TX, RX from SoC side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port on WG800HP 2. Connect power cable to WG800HP and turn on it 3. Access to "http://192.168.10.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This commit is contained in:
INAGAKI Hiroshi
Christian Lamparter
parent
99df98442e
commit
c566439c9b
@ -89,6 +89,10 @@ ath79_setup_interfaces()
|
||||
glinet,gl-x750)
|
||||
ucidef_set_interfaces_lan_wan "eth1" "eth0"
|
||||
;;
|
||||
nec,wg800hp)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "2:lan" "3:lan" "4:lan" "1:wan"
|
||||
;;
|
||||
netgear,wndr3700|\
|
||||
netgear,wndr3700v2|\
|
||||
netgear,wndr3800)
|
||||
@ -238,6 +242,10 @@ ath79_setup_macs()
|
||||
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
|
||||
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
|
||||
;;
|
||||
nec,wg800hp)
|
||||
lan_mac=$(mtd_get_mac_text board_data 640)
|
||||
wan_mac=$(mtd_get_mac_text board_data 1152)
|
||||
;;
|
||||
netgear,wndr3700|\
|
||||
netgear,wndr3700v2|\
|
||||
netgear,wndr3800)
|
||||
|
||||
@ -111,6 +111,10 @@ case "$FIRMWARE" in
|
||||
ath9k_eeprom_extract "art" 4096 1088
|
||||
ath9k_patch_fw_mac $(mtd_get_mac_ascii u-boot-env ethaddr) 2
|
||||
;;
|
||||
nec,wg800hp)
|
||||
ath9k_eeprom_extract "art" 4096 1088
|
||||
ath9k_patch_fw_mac $(mtd_get_mac_text board_data 1664) 2
|
||||
;;
|
||||
*)
|
||||
ath9k_eeprom_die "board $board is not supported yet"
|
||||
;;
|
||||
|
||||
@ -96,6 +96,10 @@ case "$FIRMWARE" in
|
||||
ath10kcal_extract "art" 20480 2116
|
||||
ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +1)
|
||||
;;
|
||||
nec,wg800hp)
|
||||
ath10kcal_extract "art" 20480 2116
|
||||
ath10kcal_patch_mac_crc $(mtd_get_mac_text board_data 2176)
|
||||
;;
|
||||
ocedo,koala)
|
||||
ath10kcal_extract "art" 20480 2116
|
||||
ath10kcal_patch_mac $(mtd_get_mac_binary art 12)
|
||||
|
||||
188
target/linux/ath79/dts/qca9563_nec_wg800hp.dts
Normal file
188
target/linux/ath79/dts/qca9563_nec_wg800hp.dts
Normal file
@ -0,0 +1,188 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "qca956x.dtsi"
|
||||
|
||||
/ {
|
||||
model = "NEC Aterm WG800HP";
|
||||
compatible = "nec,wg800hp", "qca,qca9563";
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200n8";
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &power_green;
|
||||
led-failsafe = &power_red;
|
||||
led-running = &power_green;
|
||||
led-upgrade = &power_green;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&jtag_disable_pins>;
|
||||
|
||||
wlan2g_red {
|
||||
label = "wg800hp:red:wlan2g";
|
||||
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
active_red {
|
||||
label = "wg800hp:red:active";
|
||||
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
active_green {
|
||||
label = "wg800hp:green:active";
|
||||
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
power_red: power_red {
|
||||
label = "wg800hp:red:power";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
power_green: power_green {
|
||||
label = "wg800hp:green:power";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
wlan5g_red {
|
||||
label = "wg800hp:red:wlan5g";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wlan5g_green {
|
||||
label = "wg800hp:green:wlan5g";
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
wlan2g_green {
|
||||
label = "wg800hp:green:wlan2g";
|
||||
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
br {
|
||||
label = "br";
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_0>;
|
||||
linux,input-type = <EV_SW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x040000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x050000 0x6f0000>;
|
||||
};
|
||||
|
||||
partition@740000 {
|
||||
label = "user_data";
|
||||
reg = <0x740000 0x0a0000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@7e0000 {
|
||||
label = "board_data";
|
||||
reg = <0x7e0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@7f0000 {
|
||||
label = "art";
|
||||
reg = <0x7f0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
|
||||
qca,ar8327-initvals = <
|
||||
0x04 0x00000080 /* PORT0 PAD MODE CTRL */
|
||||
0x50 0xcc35cc35 /* LED_CTRL0 */
|
||||
0x54 0xca35ca35 /* LED_CTRL1 */
|
||||
0x58 0xc935c935 /* LED_CTRL2 */
|
||||
0x5c 0x03ffff00 /* LED_CTRL3 */
|
||||
0x7c 0x0000007e /* PORT0_STATUS */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
phy-mode = "sgmii";
|
||||
phy-handle = <&phy0>;
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
qca,no-eeprom;
|
||||
};
|
||||
@ -43,6 +43,16 @@ define Build/elecom-header
|
||||
|
||||
endef
|
||||
|
||||
define Build/nec-fw
|
||||
( stat -c%s $@ | tr -d "\n" | dd bs=16 count=1 conv=sync; ) >> $@
|
||||
( \
|
||||
echo -n -e "$(1)" | dd bs=16 count=1 conv=sync; \
|
||||
echo -n "0.0.00" | dd bs=16 count=1 conv=sync; \
|
||||
dd if=$@; \
|
||||
) > $@.new
|
||||
mv $@.new $@
|
||||
endef
|
||||
|
||||
define Device/avm_fritz300e
|
||||
ATH_SOC := ar7242
|
||||
DEVICE_TITLE := AVM FRITZ!WLAN Repeater 300E
|
||||
@ -262,6 +272,19 @@ define Device/iodata_wn-ag300dgr
|
||||
endef
|
||||
TARGET_DEVICES += iodata_wn-ag300dgr
|
||||
|
||||
define Device/nec_wg800hp
|
||||
ATH_SOC := qca9563
|
||||
DEVICE_TITLE := NEC Aterm WG800HP
|
||||
IMAGE_SIZE := 7104k
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
||||
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
|
||||
xor-image -p 6A57190601121E4C004C1E1201061957 -x | \
|
||||
nec-fw LASER_ATERM
|
||||
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct-htt
|
||||
endef
|
||||
TARGET_DEVICES += nec_wg800hp
|
||||
|
||||
define Device/ocedo_koala
|
||||
ATH_SOC := qca9558
|
||||
DEVICE_TITLE := OCEDO Koala
|
||||
|
||||
Loading…
Reference in New Issue
Block a user