ath79: add support for D-Link DIR-859 A1
Hardware spec of DIR-859 A1: SoC: QCA9563 DRAM: 64MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9880 USB is supported on the PCB but not connected. Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Weijie Gao <hackpascal@gmail.com> [squash commits, use common seama recipes, sync factory image recipe with ramips version] Signed-off-by: Mathias Kresin <dev@kresin.me>
This commit is contained in:
Weijie Gao
Mathias Kresin
parent
fd35c5b205
commit
abc7ed2c58
@ -28,6 +28,9 @@ buffalo,whr-g301n)
|
||||
ucidef_set_led_switch "lan3" "LAN3" "$boardname:green:lan3" "switch0" "0x08"
|
||||
ucidef_set_led_switch "lan4" "LAN4" "$boardname:green:lan4" "switch0" "0x10"
|
||||
;;
|
||||
dlink,dir-859-a1)
|
||||
ucidef_set_led_switch "internet" "WAN" "$boardname:green:internet" "switch0" "0x20"
|
||||
;;
|
||||
etactica,eg200)
|
||||
ucidef_set_led_netdev "lan" "LAN" "$boardname:red:eth0" "eth0"
|
||||
ucidef_set_led_oneshot "modbus" "Modbus" "$boardname:red:modbus" "100" "33"
|
||||
|
||||
@ -158,6 +158,7 @@ ath79_setup_interfaces()
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan" "6@eth0"
|
||||
;;
|
||||
dlink,dir-859-a1|\
|
||||
tplink,tl-wr1043nd-v4)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
|
||||
@ -234,6 +235,10 @@ ath79_setup_macs()
|
||||
lan_mac=$(mtd_get_mac_text "mac" 4)
|
||||
wan_mac=$(mtd_get_mac_text "mac" 24)
|
||||
;;
|
||||
dlink,dir-859-a1)
|
||||
lan_mac=$(mtd_get_mac_ascii devdata "lanmac")
|
||||
wan_mac=$(mtd_get_mac_ascii devdata "wanmac")
|
||||
;;
|
||||
elecom,wrc-300ghbk2-i)
|
||||
wan_mac=$(macaddr_add "$(mtd_get_mac_binary ART 4098)" -2)
|
||||
;;
|
||||
|
||||
@ -105,6 +105,10 @@ case "$FIRMWARE" in
|
||||
ath9k_eeprom_extract "art" 4096 1088
|
||||
ath9k_patch_fw_mac_crc $(mtd_get_mac_text "mac" 4) 2
|
||||
;;
|
||||
dlink,dir-859-a1)
|
||||
ath9k_eeprom_extract "art" 4096 1088
|
||||
ath9k_patch_fw_mac $(mtd_get_mac_ascii devdata "wlan24mac") 2
|
||||
;;
|
||||
iodata,wn-ac1167dgr|\
|
||||
iodata,wn-ac1600dgr2|\
|
||||
iodata,wn-ag300dgr)
|
||||
|
||||
@ -92,6 +92,10 @@ case "$FIRMWARE" in
|
||||
ath10kcal_extract "art" 20480 2116
|
||||
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary art 0) -1)
|
||||
;;
|
||||
dlink,dir-859-a1)
|
||||
ath10kcal_extract "art" 20480 2116
|
||||
ath10kcal_patch_mac $(mtd_get_mac_ascii devdata "wlan5mac")
|
||||
;;
|
||||
glinet,gl-x750)
|
||||
ath10kcal_extract "art" 20480 2116
|
||||
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
|
||||
|
||||
@ -168,6 +168,7 @@ CONFIG_MTD_PHYSMAP=y
|
||||
CONFIG_MTD_SPI_NOR=y
|
||||
CONFIG_MTD_SPLIT_FIRMWARE=y
|
||||
CONFIG_MTD_SPLIT_LZMA_FW=y
|
||||
CONFIG_MTD_SPLIT_SEAMA_FW=y
|
||||
CONFIG_MTD_SPLIT_TPLINK_FW=y
|
||||
CONFIG_MTD_SPLIT_UIMAGE_FW=y
|
||||
CONFIG_MTD_TPLINK_PARTS=y
|
||||
|
||||
177
target/linux/ath79/dts/qca9563_dlink_dir-859-a1.dts
Normal file
177
target/linux/ath79/dts/qca9563_dlink_dir-859-a1.dts
Normal file
@ -0,0 +1,177 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "qca956x.dtsi"
|
||||
|
||||
/ {
|
||||
model = "D-Link DIR-859 A1";
|
||||
compatible = "dlink,dir-859-a1", "qca,qca9563";
|
||||
|
||||
aliases {
|
||||
led-boot = &power;
|
||||
led-failsafe = &power;
|
||||
led-running = &power;
|
||||
led-upgrade = &power;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200n8";
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
wps {
|
||||
label = "dir-859-a1:green:wps";
|
||||
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
power: power {
|
||||
label = "dir-859-a1:green:power";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
internet {
|
||||
label = "dir-859-a1:green:internet";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan {
|
||||
label = "dir-859-a1:green:wlan";
|
||||
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys-polled";
|
||||
poll-interval = <20>;
|
||||
|
||||
wps {
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
reset {
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-export {
|
||||
compatible = "gpio-export";
|
||||
#size-cells = <0>;
|
||||
|
||||
gpio_switch_reset {
|
||||
gpio-export,name = "dir-859-a1:reset:switch";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gpio {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi {
|
||||
num-cs = <1>;
|
||||
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <30000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "bootloader";
|
||||
reg = <0x000000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "bdcfg";
|
||||
reg = <0x040000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "devdata";
|
||||
reg = <0x050000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "devconf";
|
||||
reg = <0x060000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@70000 {
|
||||
compatible = "seama";
|
||||
label = "firmware";
|
||||
reg = <0x070000 0xf80000>;
|
||||
};
|
||||
|
||||
art: partition@ff0000 {
|
||||
label = "art";
|
||||
reg = <0xff0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy-mask = <0>;
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
phy-mode = "sgmii";
|
||||
|
||||
qca,ar8327-initvals = <
|
||||
0x04 0x00080080 /* PORT0 PAD MODE CTRL */
|
||||
0x10 0x81000080 /* POWER_ON_STRIP */
|
||||
0x50 0xcc35cc35 /* LED_CTRL0 */
|
||||
0x54 0xcb37cb37 /* LED_CTRL1 */
|
||||
0x58 0x00000000 /* LED_CTRL2 */
|
||||
0x5c 0x00f3cf00 /* LED_CTRL3 */
|
||||
0x7c 0x0000007e /* PORT0_STATUS */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
pll-data = <0x03000101 0x00000101 0x00001919>;
|
||||
|
||||
phy-mode = "sgmii";
|
||||
phy-handle = <&phy0>;
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
qca,no-eeprom;
|
||||
};
|
||||
@ -2,6 +2,7 @@ include ./common-buffalo.mk
|
||||
include ./common-netgear.mk
|
||||
|
||||
DEVICE_VARS += ADDPATTERN_ID ADDPATTERN_VERSION
|
||||
DEVICE_VARS += SEAMA_SIGNATURE SEAMA_MTDBLOCK
|
||||
|
||||
define Build/cybertan-trx
|
||||
@echo -n '' > $@-empty.bin
|
||||
@ -53,6 +54,23 @@ define Build/nec-fw
|
||||
mv $@.new $@
|
||||
endef
|
||||
|
||||
define Device/seama
|
||||
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
|
||||
KERNEL_INITRAMFS := $$(KERNEL) | seama
|
||||
IMAGES += factory.bin
|
||||
SEAMA_MTDBLOCK := 1
|
||||
|
||||
# 64 bytes offset:
|
||||
# - 28 bytes seama_header
|
||||
# - 36 bytes of META data (4-bytes aligned)
|
||||
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
|
||||
IMAGE/sysupgrade.bin := \
|
||||
$$(IMAGE/default) | seama | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
|
||||
IMAGE/factory.bin := \
|
||||
$$(IMAGE/default) | pad-rootfs -x 64 | seama | seama-seal | check-size $$$$(IMAGE_SIZE)
|
||||
SEAMA_SIGNATURE :=
|
||||
endef
|
||||
|
||||
define Device/avm_fritz300e
|
||||
ATH_SOC := ar7242
|
||||
DEVICE_TITLE := AVM FRITZ!WLAN Repeater 300E
|
||||
@ -192,6 +210,17 @@ define Device/dlink_dir-835-a1
|
||||
endef
|
||||
TARGET_DEVICES += dlink_dir-835-a1
|
||||
|
||||
define Device/dlink_dir-859-a1
|
||||
$(Device/seama)
|
||||
ATH_SOC := qca9563
|
||||
DEVICE_TITLE := D-LINK DIR-859 A1
|
||||
IMAGE_SIZE := 15872k
|
||||
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
||||
SEAMA_SIGNATURE := wrgac37_dlink.2013gui_dir859
|
||||
SUPPORTED_DEVICES += dir-859-a1
|
||||
endef
|
||||
TARGET_DEVICES += dlink_dir-859-a1
|
||||
|
||||
define Device/elecom_wrc-300ghbk2-i
|
||||
ATH_SOC := qca9563
|
||||
DEVICE_TITLE := ELECOM WRC-300GHBK2-I
|
||||
|
||||
Loading…
Reference in New Issue
Block a user