ipq806x/nbg6817: add support for ZyXEL NBG6817
CPU: 2x1.8GHz ARM, RAM: 512MiB Storage: 4MiB serial Flash, 3.9GiB MMC NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin to device. Then run: cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4 cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5 reboot -f For debugging serial console is easily visible on board, no soldering needed. Signed-off-by: André Valentin <avalentin@marcant.net>
This commit is contained in:
André Valentin
John Crispin
parent
91b518512d
commit
a0ed7af6c6
@ -33,6 +33,11 @@ ea8500)
|
||||
ucidef_set_led_wlan "wifi" "WIFI" "ea8500:green:wifi" "phy0radio"
|
||||
ucidef_set_led_default "wps" "WPS" "ea8500:green:wps" "0"
|
||||
;;
|
||||
nbg6817)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2g" "$board:amber:wifi" "phy1radio"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN5G" "$board:amber:wifi5" "phy0radio"
|
||||
ucidef_set_led_netdev "wan" "WAN" "$board:white:internet" "eth1"
|
||||
;;
|
||||
*)
|
||||
;;
|
||||
esac
|
||||
|
||||
@ -35,6 +35,13 @@ ea8500)
|
||||
ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
|
||||
ucidef_set_interface_macaddr "wan" "$hw_mac_addr"
|
||||
;;
|
||||
nbg6817)
|
||||
hw_mac_addr=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
|
||||
ucidef_add_switch "switch0" \
|
||||
"1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0"
|
||||
ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
|
||||
ucidef_set_interface_macaddr "wan" "$(macaddr_add $hw_mac_addr 1)"
|
||||
;;
|
||||
*)
|
||||
echo "Unsupported hardware. Network interfaces not intialized"
|
||||
;;
|
||||
|
||||
@ -56,6 +56,9 @@ case "$FIRMWARE" in
|
||||
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
||||
ath10kcal_extract "art" 4096 12064
|
||||
;;
|
||||
nbg6817)
|
||||
ath10kcal_extract "0:ART" 4096 12064
|
||||
;;
|
||||
r7500v2 |\
|
||||
r7800)
|
||||
ath10kcal_extract "art" 4096 12064
|
||||
@ -72,6 +75,9 @@ case "$FIRMWARE" in
|
||||
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
||||
ath10kcal_extract "art" 20480 12064
|
||||
;;
|
||||
nbg6817)
|
||||
ath10kcal_extract "0:ART" 20480 12064
|
||||
;;
|
||||
r7500v2 |\
|
||||
r7800)
|
||||
ath10kcal_extract "art" 20480 12064
|
||||
|
||||
@ -26,6 +26,9 @@ ipq806x_board_detect() {
|
||||
*"DB149")
|
||||
name="db149"
|
||||
;;
|
||||
*"NBG6817")
|
||||
name="nbg6817"
|
||||
;;
|
||||
*"R7500")
|
||||
name="r7500"
|
||||
;;
|
||||
|
||||
@ -61,6 +61,7 @@ CONFIG_ARM_THUMB=y
|
||||
CONFIG_ARM_UNWIND=y
|
||||
CONFIG_ARM_VIRT_EXT=y
|
||||
CONFIG_AT803X_PHY=y
|
||||
CONFIG_BLK_DEV_LOOP=y
|
||||
# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
|
||||
CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
|
||||
CONFIG_BOUNCE=y
|
||||
@ -197,11 +198,6 @@ CONFIG_HAVE_GENERIC_DMA_COHERENT=y
|
||||
CONFIG_HAVE_HW_BREAKPOINT=y
|
||||
CONFIG_HAVE_IDE=y
|
||||
CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
|
||||
CONFIG_HAVE_KERNEL_GZIP=y
|
||||
CONFIG_HAVE_KERNEL_LZ4=y
|
||||
CONFIG_HAVE_KERNEL_LZMA=y
|
||||
CONFIG_HAVE_KERNEL_LZO=y
|
||||
CONFIG_HAVE_KERNEL_XZ=y
|
||||
CONFIG_HAVE_MEMBLOCK=y
|
||||
CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
|
||||
CONFIG_HAVE_NET_DSA=y
|
||||
@ -262,6 +258,16 @@ CONFIG_MFD_SYSCON=y
|
||||
CONFIG_MIGHT_HAVE_CACHE_L2X0=y
|
||||
CONFIG_MIGHT_HAVE_PCI=y
|
||||
CONFIG_MIGRATION=y
|
||||
CONFIG_MMC=y
|
||||
CONFIG_MMC_ARMMMCI=y
|
||||
CONFIG_MMC_BLOCK=y
|
||||
CONFIG_MMC_BLOCK_MINORS=16
|
||||
CONFIG_MMC_QCOM_DML=y
|
||||
CONFIG_MMC_SDHCI=y
|
||||
CONFIG_MMC_SDHCI_MSM=y
|
||||
# CONFIG_MMC_SDHCI_PCI is not set
|
||||
CONFIG_MMC_SDHCI_PLTFM=y
|
||||
# CONFIG_MMC_TIFM_SD is not set
|
||||
CONFIG_MODULES_TREE_LOOKUP=y
|
||||
CONFIG_MODULES_USE_ELF_REL=y
|
||||
CONFIG_MSM_GCC_8660=y
|
||||
@ -378,7 +384,6 @@ CONFIG_QCOM_SCM=y
|
||||
CONFIG_QCOM_SCM_32=y
|
||||
# CONFIG_QCOM_SMD is not set
|
||||
CONFIG_QCOM_SMEM=y
|
||||
# CONFIG_QCOM_SPMI_TEMP_ALARM is not set
|
||||
CONFIG_QCOM_WDT=y
|
||||
CONFIG_RAS=y
|
||||
CONFIG_RATIONAL=y
|
||||
@ -389,6 +394,7 @@ CONFIG_RD_GZIP=y
|
||||
CONFIG_REGMAP=y
|
||||
CONFIG_REGMAP_MMIO=y
|
||||
CONFIG_REGULATOR=y
|
||||
CONFIG_REGULATOR_FIXED_VOLTAGE=y
|
||||
CONFIG_REGULATOR_QCOM_RPM=y
|
||||
# CONFIG_REGULATOR_QCOM_SPMI is not set
|
||||
CONFIG_RESET_CONTROLLER=y
|
||||
|
||||
@ -0,0 +1,341 @@
|
||||
#include "qcom-ipq8065-v1.0.dtsi"
|
||||
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
model = "ZyXEL NBG6817";
|
||||
compatible = "zyxel,nbg6817", "qcom,ipq8065";
|
||||
|
||||
memory@0 {
|
||||
reg = <0x42000000 0x1e000000>;
|
||||
device_type = "memory";
|
||||
};
|
||||
|
||||
reserved-memory {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
ranges;
|
||||
rsvd@41200000 {
|
||||
reg = <0x41200000 0x300000>;
|
||||
no-map;
|
||||
};
|
||||
};
|
||||
|
||||
aliases {
|
||||
serial0 = &uart4;
|
||||
mdio-gpio0 = &mdio0;
|
||||
sdcc1 = &sdcc1;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "root=/dev/mmcblk0p5 rootfstype=squashfs,ext4 rootwait noinitrd";
|
||||
linux,stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
soc {
|
||||
pinmux@800000 {
|
||||
pinctrl-0 = <&mdio0_pins &rgmii2_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
i2c4_pins: i2c4_pinmux {
|
||||
mux {
|
||||
pins = "gpio12", "gpio13";
|
||||
function = "gsbi4";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
mdio0_pins: mdio0_pins {
|
||||
mux {
|
||||
pins = "gpio0", "gpio1";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
clk {
|
||||
pins = "gpio1";
|
||||
input-disable;
|
||||
};
|
||||
};
|
||||
|
||||
rgmii2_pins: rgmii2_pins {
|
||||
mux {
|
||||
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
|
||||
"gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
|
||||
function = "rgmii2";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
tx {
|
||||
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
|
||||
input-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_pins: spi_pins {
|
||||
mux {
|
||||
pins = "gpio18", "gpio19", "gpio21";
|
||||
function = "gsbi5";
|
||||
drive-strength = <10>;
|
||||
bias-none;
|
||||
};
|
||||
|
||||
cs {
|
||||
pins = "gpio20";
|
||||
drive-strength = <12>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
gsbi@16300000 {
|
||||
qcom,mode = <GSBI_PROT_I2C_UART>;
|
||||
status = "ok";
|
||||
serial@16340000 {
|
||||
status = "ok";
|
||||
};
|
||||
/*
|
||||
* The i2c device on gsbi4 should not be enabled.
|
||||
* On ipq806x designs gsbi4 i2c is meant for exclusive
|
||||
* RPM usage. Turning this on in kernel manifests as
|
||||
* i2c failure for the RPM.
|
||||
*/
|
||||
};
|
||||
|
||||
gsbi5: gsbi@1a200000 {
|
||||
qcom,mode = <GSBI_PROT_SPI>;
|
||||
status = "ok";
|
||||
|
||||
spi4: spi@1a280000 {
|
||||
status = "ok";
|
||||
spi-max-frequency = <50000000>;
|
||||
pinctrl-0 = <&spi_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash: m25p80@0 {
|
||||
compatible = "s25fl512s";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
spi-max-frequency = <51200000>;
|
||||
reg = <0>;
|
||||
|
||||
linux,part-probe = "qcom-smem";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
phy@100f8800 { /* USB3 port 1 HS phy */
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
phy@100f8830 { /* USB3 port 1 SS phy */
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
phy@110f8800 { /* USB3 port 0 HS phy */
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
phy@110f8830 { /* USB3 port 0 SS phy */
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
usb30@0 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
usb30@1 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
pcie0: pci@1b500000 {
|
||||
status = "ok";
|
||||
reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-0 = <&pcie0_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
pcie1: pci@1b700000 {
|
||||
status = "ok";
|
||||
reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-0 = <&pcie1_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
mdio0: mdio {
|
||||
compatible = "virtual,mdio-gpio";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
device_type = "ethernet-phy";
|
||||
reg = <0>;
|
||||
qca,ar8327-initvals = <
|
||||
0x00004 0x7600000 /* PAD0_MODE */
|
||||
0x00008 0x1000000 /* PAD5_MODE */
|
||||
0x0000c 0x80 /* PAD6_MODE */
|
||||
0x000e4 0xaa545 /* MAC_POWER_SEL */
|
||||
0x000e0 0xc74164de /* SGMII_CTRL */
|
||||
0x0007c 0x4e /* PORT0_STATUS */
|
||||
0x00094 0x4e /* PORT6_STATUS */
|
||||
0x00970 0x1e864443 /* QM_PORT0_CTRL0 */
|
||||
0x00974 0x000001c6 /* QM_PORT0_CTRL1 */
|
||||
0x00978 0x19008643 /* QM_PORT1_CTRL0 */
|
||||
0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */
|
||||
0x00980 0x19008643 /* QM_PORT2_CTRL0 */
|
||||
0x00984 0x000001c6 /* QM_PORT2_CTRL1 */
|
||||
0x00988 0x19008643 /* QM_PORT3_CTRL0 */
|
||||
0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */
|
||||
0x00990 0x19008643 /* QM_PORT4_CTRL0 */
|
||||
0x00994 0x000001c6 /* QM_PORT4_CTRL1 */
|
||||
0x00998 0x1e864443 /* QM_PORT5_CTRL0 */
|
||||
0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */
|
||||
0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */
|
||||
0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */
|
||||
>;
|
||||
};
|
||||
|
||||
phy4: ethernet-phy@4 {
|
||||
device_type = "ethernet-phy";
|
||||
reg = <4>;
|
||||
qca,ar8327-initvals = <
|
||||
0x000e4 0x6a545 /* MAC_POWER_SEL */
|
||||
0x0000c 0x80 /* PAD6_MODE */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
gmac1: ethernet@37200000 {
|
||||
status = "ok";
|
||||
phy-mode = "rgmii";
|
||||
qcom,id = <1>;
|
||||
qcom,phy_mdio_addr = <4>;
|
||||
qcom,poll_required = <0>;
|
||||
qcom,rgmii_delay = <1>;
|
||||
qcom,phy_mii_type = <0>;
|
||||
qcom,emulation = <0>;
|
||||
qcom,irq = <255>;
|
||||
mdiobus = <&mdio0>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
gmac2: ethernet@37400000 {
|
||||
status = "ok";
|
||||
phy-mode = "sgmii";
|
||||
qcom,id = <2>;
|
||||
qcom,phy_mdio_addr = <0>; /* none */
|
||||
qcom,poll_required = <0>; /* no polling */
|
||||
qcom,rgmii_delay = <0>;
|
||||
qcom,phy_mii_type = <1>;
|
||||
qcom,emulation = <0>;
|
||||
qcom,irq = <258>;
|
||||
mdiobus = <&mdio0>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
rpm@108000 {
|
||||
pinctrl-0 = <&i2c4_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
amba {
|
||||
sdcc1: sdcc@12400000 {
|
||||
status = "okay";
|
||||
dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
|
||||
dma-names = "tx", "rx";
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
wifi {
|
||||
label = "wifi";
|
||||
gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RFKILL>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
internet {
|
||||
label = "nbg6817:white:internet";
|
||||
gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
power {
|
||||
label = "nbg6817:white:power";
|
||||
gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
wifi {
|
||||
label = "nbg6817:amber:wifi";
|
||||
gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wifi5g {
|
||||
label = "nbg6817:amber:wifi5g";
|
||||
gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio_export {
|
||||
compatible = "gpio-export";
|
||||
#size-cells = <0>;
|
||||
|
||||
usb0_status {
|
||||
gpio-export,name = "usb0";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&qcom_pinmux 15 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
usb1_status {
|
||||
gpio-export,name = "usb1";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
usb1_power {
|
||||
gpio-export,name = "usb1_power";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&qcom_pinmux 14 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
usb2_power {
|
||||
gpio-export,name = "usb2_power";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&adm_dma {
|
||||
status = "ok";
|
||||
};
|
||||
@ -90,6 +90,19 @@ define Device/TpSafeImage
|
||||
endef
|
||||
DEVICE_VARS += TPLINK_BOARD_NAME
|
||||
|
||||
define Device/ZyXELImage
|
||||
PROFILES += $$(DEVICE_NAME)
|
||||
FILESYSTEMS := squashfs
|
||||
KERNEL_SUFFIX := -uImage
|
||||
KERNEL = kernel-bin | append-dtb | uImage none | pad-to $$$${KERNEL_SIZE}
|
||||
KERNEL_NAME := zImage
|
||||
IMAGES := sysupgrade.tar mmcblk0p5-rootfs.bin mmcblk0p4-kernel.bin
|
||||
IMAGE/sysupgrade.tar/squashfs := append-rootfs | pad-to $$$${BLOCKSIZE} | sysupgrade-tar rootfs=$$$$@
|
||||
IMAGE/sysupgrade.tar := sysupgrade-tar
|
||||
IMAGE/mmcblk0p5-rootfs.bin := append-rootfs | pad-rootfs | pad-to $$$${BLOCKSIZE}
|
||||
IMAGE/mmcblk0p4-kernel.bin := append-kernel
|
||||
endef
|
||||
|
||||
define Device/AP148
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
@ -202,6 +215,16 @@ define Device/R7800
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9984
|
||||
endef
|
||||
|
||||
TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2 R7800
|
||||
define Device/NBG6817
|
||||
DEVICE_DTS := qcom-ipq8065-nbg6817
|
||||
KERNEL_SIZE := 4096k
|
||||
BLOCKSIZE := 64k
|
||||
BOARD_NAME := nbg6817
|
||||
DEVICE_TITLE := ZyXEL NBG6817
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9984 e2fsprogs losetup
|
||||
$(call Device/ZyXELImage)
|
||||
endef
|
||||
|
||||
TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2 R7800 NBG6817
|
||||
|
||||
$(eval $(call BuildImage))
|
||||
|
||||
@ -12,7 +12,7 @@ Signed-off-by: Jonas Gorski <jogo@openwrt.org>
|
||||
|
||||
--- a/arch/arm/boot/dts/Makefile
|
||||
+++ b/arch/arm/boot/dts/Makefile
|
||||
@@ -506,7 +506,13 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
@@ -506,7 +506,14 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
qcom-apq8084-ifc6540.dtb \
|
||||
qcom-apq8084-mtp.dtb \
|
||||
qcom-ipq8064-ap148.dtb \
|
||||
@ -22,6 +22,7 @@ Signed-off-by: Jonas Gorski <jogo@openwrt.org>
|
||||
+ qcom-ipq8064-ea8500.dtb \
|
||||
+ qcom-ipq8064-r7500.dtb \
|
||||
+ qcom-ipq8064-r7500v2.dtb \
|
||||
+ qcom-ipq8065-nbg6817.dtb \
|
||||
+ qcom-ipq8065-r7800.dtb \
|
||||
qcom-msm8660-surf.dtb \
|
||||
qcom-msm8960-cdp.dtb \
|
||||
|
||||
Loading…
Reference in New Issue
Block a user