ipq806x: add support for OpenMesh A42
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
- 802.3af POE on Ethernet 1
- 18-24v passive POE (mode B) on Ethernet 2
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
This commit is contained in:
Sven Eckelmann
Mathias Kresin
parent
c242643d1a
commit
86e18f6706
@ -33,6 +33,9 @@ tplink,vr2600v)
|
||||
ucidef_add_switch "switch0" \
|
||||
"1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0"
|
||||
;;
|
||||
openmesh,a42)
|
||||
ucidef_set_interfaces_lan_wan "eth1" "eth0"
|
||||
;;
|
||||
qcom,ipq8064-db149)
|
||||
ucidef_set_interface_lan "eth1 eth2 eth3"
|
||||
ucidef_add_switch "switch0" \
|
||||
|
||||
@ -50,6 +50,9 @@ case "$FIRMWARE" in
|
||||
avm,fritzbox-4040)
|
||||
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
|
||||
;;
|
||||
openmesh,a42)
|
||||
ath10kcal_extract "0:ART" 4096 12064
|
||||
;;
|
||||
qcom,ap-dk01.1-c1)
|
||||
ath10kcal_extract "ART" 4096 12064
|
||||
;;
|
||||
@ -60,6 +63,9 @@ case "$FIRMWARE" in
|
||||
avm,fritzbox-4040)
|
||||
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
|
||||
;;
|
||||
openmesh,a42)
|
||||
ath10kcal_extract "0:ART" 20480 12064
|
||||
;;
|
||||
qcom,ap-dk01.1-c1)
|
||||
ath10kcal_extract "ART" 20480 12064
|
||||
;;
|
||||
|
||||
110
target/linux/ipq806x/base-files/lib/upgrade/openmesh.sh
Normal file
110
target/linux/ipq806x/base-files/lib/upgrade/openmesh.sh
Normal file
@ -0,0 +1,110 @@
|
||||
# The U-Boot loader of the OpenMesh devices requires image sizes and
|
||||
# checksums to be provided in the U-Boot environment.
|
||||
# The OpenMesh devices come with 2 main partitions - while one is active
|
||||
# sysupgrade will flash the other. The boot order is changed to boot the
|
||||
# newly flashed partition. If the new partition can't be booted due to
|
||||
# upgrade failures the previously used partition is loaded.
|
||||
|
||||
platform_do_upgrade_openmesh() {
|
||||
local tar_file="$1"
|
||||
local restore_backup
|
||||
local primary_kernel_mtd
|
||||
|
||||
local setenv_script="/tmp/fw_env_upgrade"
|
||||
|
||||
local kernel_mtd="$(find_mtd_index $PART_NAME)"
|
||||
local kernel_offset="$(cat /sys/class/mtd/mtd${kernel_mtd}/offset)"
|
||||
local total_size="$(cat /sys/class/mtd/mtd${kernel_mtd}/size)"
|
||||
|
||||
# detect to which flash region the new image is written to.
|
||||
#
|
||||
# 1. check what is the mtd index for the first flash region on this
|
||||
# device
|
||||
# 2. check if the target partition ("inactive") has the mtd index of
|
||||
# the first flash region
|
||||
#
|
||||
# - when it is: the new bootseq will be 1,2 and the first region is
|
||||
# modified
|
||||
# - when it isnt: bootseq will be 2,1 and the second region is
|
||||
# modified
|
||||
#
|
||||
# The detection has to be done via the hardcoded mtd partition because
|
||||
# the current boot might be done with the fallback region. Let us
|
||||
# assume that the current bootseq is 1,2. The bootloader detected that
|
||||
# the image in flash region 1 is corrupt and thus switches to flash
|
||||
# region 2. The bootseq in the u-boot-env is now still the same and
|
||||
# the sysupgrade code can now only rely on the actual mtd indexes and
|
||||
# not the bootseq variable to detect the currently booted flash
|
||||
# region/image.
|
||||
#
|
||||
# In the above example, an implementation which uses bootseq ("1,2") to
|
||||
# detect the currently booted image would assume that region 1 is booted
|
||||
# and then overwrite the variables for the wrong flash region (aka the
|
||||
# one which isn't modified). This could result in a device which doesn't
|
||||
# boot anymore to Linux until it was reflashed with ap51-flash.
|
||||
local next_boot_part="1"
|
||||
case "$(board_name)" in
|
||||
openmesh,a42)
|
||||
primary_kernel_mtd=8
|
||||
;;
|
||||
*)
|
||||
echo "failed to detect primary kernel mtd partition for board"
|
||||
return 1
|
||||
;;
|
||||
esac
|
||||
[ "$kernel_mtd" = "$primary_kernel_mtd" ] || next_boot_part="2"
|
||||
|
||||
local board_dir=$(tar tf $tar_file | grep -m 1 '^sysupgrade-.*/$')
|
||||
board_dir=${board_dir%/}
|
||||
|
||||
local kernel_length=$(tar xf $tar_file ${board_dir}/kernel -O | wc -c)
|
||||
local rootfs_length=$(tar xf $tar_file ${board_dir}/root -O | wc -c)
|
||||
# rootfs without EOF marker
|
||||
rootfs_length=$((rootfs_length-4))
|
||||
|
||||
local kernel_md5=$(tar xf $tar_file ${board_dir}/kernel -O | md5sum); kernel_md5="${kernel_md5%% *}"
|
||||
# md5 checksum of rootfs with EOF marker
|
||||
local rootfs_md5=$(tar xf $tar_file ${board_dir}/root -O | dd bs=1 count=$rootfs_length | md5sum); rootfs_md5="${rootfs_md5%% *}"
|
||||
|
||||
#
|
||||
# add tar support to get_image() to use default_do_upgrade() instead?
|
||||
#
|
||||
|
||||
# take care of restoring a saved config
|
||||
[ "$SAVE_CONFIG" -eq 1 ] && restore_backup="${MTD_CONFIG_ARGS} -j ${CONF_TAR}"
|
||||
|
||||
# write concatinated kernel + rootfs to flash
|
||||
tar xf $tar_file ${board_dir}/kernel ${board_dir}/root -O | \
|
||||
mtd $restore_backup write - $PART_NAME
|
||||
|
||||
# prepare new u-boot env
|
||||
if [ "$next_boot_part" = "1" ]; then
|
||||
echo "bootseq 1,2" > $setenv_script
|
||||
else
|
||||
echo "bootseq 2,1" > $setenv_script
|
||||
fi
|
||||
|
||||
printf "kernel_size_%i 0x%08x\n" $next_boot_part $kernel_length >> $setenv_script
|
||||
printf "vmlinux_start_addr 0x%08x\n" ${kernel_offset} >> $setenv_script
|
||||
printf "vmlinux_size 0x%08x\n" ${kernel_length} >> $setenv_script
|
||||
printf "vmlinux_checksum %s\n" ${kernel_md5} >> $setenv_script
|
||||
|
||||
printf "rootfs_size_%i 0x%08x\n" $next_boot_part $((total_size-kernel_length)) >> $setenv_script
|
||||
printf "rootfs_start_addr 0x%08x\n" $((kernel_offset+kernel_length)) >> $setenv_script
|
||||
printf "rootfs_size 0x%08x\n" ${rootfs_length} >> $setenv_script
|
||||
printf "rootfs_checksum %s\n" ${rootfs_md5} >> $setenv_script
|
||||
|
||||
# store u-boot env changes
|
||||
fw_setenv -s $setenv_script || {
|
||||
echo "failed to update U-Boot environment"
|
||||
return 1
|
||||
}
|
||||
}
|
||||
|
||||
# create /var/lock for the lock "fw_setenv.lock" of fw_setenv
|
||||
# the rest is copied using ipq806x's RAMFS_COPY_BIN and RAMFS_COPY_DATA
|
||||
platform_add_ramfs_ubootenv()
|
||||
{
|
||||
mkdir -p $RAM_ROOT/var/lock
|
||||
}
|
||||
append sysupgrade_pre_upgrade platform_add_ramfs_ubootenv
|
||||
@ -22,6 +22,10 @@ platform_do_upgrade() {
|
||||
zyxel,nbg6817)
|
||||
nand_do_upgrade "$ARGV"
|
||||
;;
|
||||
openmesh,a42)
|
||||
PART_NAME="inactive"
|
||||
platform_do_upgrade_openmesh "$ARGV"
|
||||
;;
|
||||
tplink,c2600)
|
||||
PART_NAME="os-image:rootfs"
|
||||
MTD_CONFIG_ARGS="-s 0x200000"
|
||||
|
||||
@ -0,0 +1,244 @@
|
||||
/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
|
||||
* Copyright (c) 2017, Sven Eckelmann <sven.eckelmann@openmesh.com>
|
||||
*
|
||||
* Permission to use, copy, modify, and/or distribute this software for any
|
||||
* purpose with or without fee is hereby granted, provided that the above
|
||||
* copyright notice and this permission notice appear in all copies.
|
||||
*
|
||||
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
|
||||
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
|
||||
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
|
||||
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
|
||||
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
|
||||
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
|
||||
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
|
||||
*
|
||||
*/
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include "qcom-ipq4019-bus.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "OpenMesh A42";
|
||||
compatible = "openmesh,a42", "qcom,ipq4019";
|
||||
|
||||
reserved-memory {
|
||||
#address-cells = <0x1>;
|
||||
#size-cells = <0x1>;
|
||||
ranges;
|
||||
|
||||
rsvd1@87000000 {
|
||||
reg = <0x87000000 0x500000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
wifi_dump@87500000 {
|
||||
reg = <0x87500000 0x600000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
rsvd2@87B00000 {
|
||||
reg = <0x87b00000 0x500000>;
|
||||
no-map;
|
||||
};
|
||||
};
|
||||
|
||||
soc {
|
||||
tcsr@194b000 {
|
||||
/* select hostmode */
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
pinctrl@1000000 {
|
||||
serial_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio60", "gpio61";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_0_pins: spi_0_pinmux {
|
||||
pinmux {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio55", "gpio56", "gpio57";
|
||||
};
|
||||
pinmux_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio54";
|
||||
};
|
||||
pinconf {
|
||||
pins = "gpio55", "gpio56", "gpio57";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
pinconf_cs {
|
||||
pins = "gpio54";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
blsp_dma: dma@7884000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
spi_0: spi@78b5000 {
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "ok";
|
||||
cs-gpios = <&tlmm 54 0>;
|
||||
|
||||
m25p80@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
/* partitions are passed via bootloader */
|
||||
};
|
||||
};
|
||||
|
||||
serial@78af000 {
|
||||
pinctrl-0 = <&serial_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
cryptobam: dma@8e04000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
usb2_hs_phy: hsphy@a8000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
usb2: usb2@60f8800 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
wifi@a000000 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "OM-A42";
|
||||
};
|
||||
|
||||
wifi@a800000 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "OM-A42";
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 59 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &power;
|
||||
led-failsafe = &power;
|
||||
led-running = &power;
|
||||
led-upgrade = &power;
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
red {
|
||||
label = "a42:red:status";
|
||||
gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "default-off";
|
||||
};
|
||||
|
||||
power: green {
|
||||
label = "a42:green:status";
|
||||
gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
blue {
|
||||
label = "a42:blue:status";
|
||||
gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "default-off";
|
||||
};
|
||||
};
|
||||
|
||||
watchdog {
|
||||
compatible = "linux,wdt-gpio";
|
||||
gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
|
||||
hw_algo = "toggle";
|
||||
/* hw_margin_ms is actually 300s but driver limits it to 60s */
|
||||
hw_margin_ms = <60000>;
|
||||
always-running;
|
||||
};
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
qcom,phy_mdio_addr = <4>;
|
||||
qcom,poll_required = <1>;
|
||||
qcom,forced_speed = <1000>;
|
||||
qcom,forced_duplex = <1>;
|
||||
vlan_tag = <2 0x20>;
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
qcom,phy_mdio_addr = <3>;
|
||||
qcom,poll_required = <1>;
|
||||
qcom,forced_speed = <1000>;
|
||||
qcom,forced_duplex = <1>;
|
||||
vlan_tag = <1 0x10>;
|
||||
};
|
||||
@ -192,6 +192,23 @@ define Device/netgear_r7800
|
||||
endef
|
||||
TARGET_DEVICES += netgear_r7800
|
||||
|
||||
define Device/openmesh_a42
|
||||
$(call Device/FitImageLzma)
|
||||
FILESYSTEMS := squashfs
|
||||
DEVICE_DTS := qcom-ipq4019-a42
|
||||
KERNEL_LOADADDR := 0x80208000
|
||||
BLOCKSIZE := 64k
|
||||
SUPPORTED_DEVICES := openmesh,a42
|
||||
DEVICE_TITLE := OpenMesh A42
|
||||
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
||||
IMAGE_SIZE := 15616k
|
||||
IMAGES = factory.bin sysupgrade.bin
|
||||
IMAGE/factory.bin/squashfs := append-rootfs | pad-rootfs | openmesh-image ce_type=A42
|
||||
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca4019 uboot-envtools ipq-wifi-openmesh_a42
|
||||
endef
|
||||
TARGET_DEVICES += openmesh_a42
|
||||
|
||||
define Device/qcom_ap-dk01.1-c1
|
||||
PROFILES += $$(DEVICE_NAME)
|
||||
DEVICE_TITLE := QCA AP-DK01.1-C1
|
||||
|
||||
@ -10,8 +10,11 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
|
||||
--- a/arch/arm/boot/dts/Makefile
|
||||
+++ b/arch/arm/boot/dts/Makefile
|
||||
@@ -618,7 +618,16 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
@@ -616,9 +616,19 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
qcom-apq8074-dragonboard.dtb \
|
||||
qcom-apq8084-ifc6540.dtb \
|
||||
qcom-apq8084-mtp.dtb \
|
||||
+ qcom-ipq4019-a42.dtb \
|
||||
qcom-ipq4019-ap.dk01.1-c1.dtb \
|
||||
qcom-ipq4019-ap.dk04.1-c1.dtb \
|
||||
+ qcom-ipq4019-fritz4040.dtb \
|
||||
|
||||
Loading…
Reference in New Issue
Block a user