mvebu: uDPU: add sysupgrade support

This patch adds sysupgrade, uboot-env and networking support
for Methode uDPU device.

Device features 4 partitions:

-----------------------------------------
|  boot   | recovery  | rootfs |  misc  |
| (ext4)  |  (ext4)   | (fsf2) | (f2fs) |
_________________________________________

Idea was to use f2fs only but the u-boot currently lacks support
so first 2 partition are ext4 to be u-boot readable, and this was
a reason why custom build and sysupgrade sections were required.

On the sysupgrade, boot and rootfs partitions are updated, firmare
image and user configuration is saved on the misc partition and if
the upgrade was successfull, recovery partition will be updated on
after the reboot from preinit script. If the sysupgrade fails for any
reason, device will fallback to recovery initramfs image.

Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>

package/boot/uboot-envtools/files/mvebu

@@ -36,6 +36,9 @@ linksys,rango|\
 linksys,venom)
 	ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000"
 	;;
+methode,udpu)
+	ubootenv_add_uci_config "/dev/mtd0" "0x180000" "0x10000" "0x10000"
+	;;
 esac
 
 config_load ubootenv

target/linux/mvebu/base-files/etc/board.d/02_network

@@ -49,7 +49,7 @@ marvell,armada-3720-db)
 marvell,axp-gp)
 	ucidef_set_interface_lan "eth0 eth1 eth2 eth3"
 	;;
-methode,uDPU)
+methode,udpu)
 	ucidef_set_interfaces_lan_wan "eth1" "eth0"
 	;;
 solidrun,clearfog*a1)

target/linux/mvebu/base-files/lib/preinit/82_uDPU

@@ -0,0 +1,48 @@
+#
+# Copyright (C) 2014-2019 OpenWrt.org
+# Copyright (C) 2016 LEDE-Project.org
+#
+
+preinit_mount_udpu() {
+
+	. /lib/functions.sh
+
+	case $(board_name) in
+	methode,udpu)
+		# Check which device is detected
+		[ -b "/dev/mmcblk0" ] && mmcdev="/dev/mmcblk0" || mmcdev="/dev/mmcblk1"
+
+		if [ -b "${mmcdev}p4" ]; then
+			mkdir /misc
+			mount -t f2fs ${mmcdev}p4 /misc
+			[ -f "/misc/sysupgrade.tgz" ] && {
+				echo "- Restoring configuration files -"
+				tar xzf /misc/sysupgrade.tgz -C /
+				rm -f /misc/sysupgrade.tgz
+				sync
+			}
+			[ -f "/misc/firmware/recovery.itb" ] && {
+					echo "- Updating /recovery partition -"
+					mkfs.ext4 -q ${mmcdev}p2 | echo y &> /dev/null
+					mkdir -p /tmp/recovery
+					mount ${mmcdev}p2 /tmp/recovery
+					cp /misc/firmware/recovery.itb /tmp/recovery
+					[ -f "/misc/firmware/boot.scr" ] && \
+						cp /misc/firmware/boot.scr /tmp/recovery
+					sync
+					umount /tmp/recovery
+					rm -rf /tmp/recovery
+
+					# Replace previous backup with the new one
+					[ -d "/misc/firmware_old" ] && rm -rf /misc/firmware_old
+					[ -d "/misc/firmware" ] && mv /misc/firmware /misc/firmware_old
+				}
+		fi
+
+		# Legacy support - if rootfs was booted, instruct u-boot to keep the current root dev
+		[ "$(df | grep /dev/root)" ] && fw_setenv root_ok '2'
+	;;
+	esac
+}
+
+boot_hook_add preinit_main preinit_mount_udpu

target/linux/mvebu/base-files/lib/upgrade/platform.sh

@@ -28,6 +28,9 @@ platform_do_upgrade() {
 	marvell,armada8040-mcbin|solidrun,clearfog-base-a1|solidrun,clearfog-pro-a1)
 		platform_do_upgrade_sdcard "$1"
 		;;
+	methode,udpu)
+		platform_do_upgrade_uDPU "$1"
+		;;
 	*)
 		default_do_upgrade "$1"
 		;;
@@ -42,5 +45,8 @@ platform_copy_config() {
 	marvell,armada8040-mcbin|solidrun,clearfog-base-a1|solidrun,clearfog-pro-a1)
 		platform_copy_config_sdcard
 		;;
+	methode,udpu)
+		platform_copy_config_uDPU
+		;;
 	esac
 }

target/linux/mvebu/base-files/lib/upgrade/uDPU.sh

@@ -0,0 +1,152 @@
+# uDPU uses combined ext4 and f2fs partitions.
+# partition layout:
+#	1. boot	(ext4)
+#	2. recovery  (ext4)
+#	3. rootfs (f2fs)
+#	4. misc (f2fs)
+
+# Check which device is available, depending on the board revision
+if [ -b "/dev/mmcblk1" ]; then
+	emmc_dev=/dev/mmcblk1
+elif [ -b "/dev/mmcblk0" ]; then
+	emmc_dev=/dev/mmcblk0
+else
+	echo "Cannot detect eMMC flash, aborting.."
+	exit 1
+fi
+
+part_prep() {
+	 if [ "$(grep $1 /proc/mounts)" ]; then
+		mounted_part="$(grep $1 /proc/mounts | awk '{print $2}' | head -1)"
+		umount $mounted_part
+		[ "$(grep -wo $mounted_part /proc/mounts)" ] && umount -l $mounted_part
+	fi
+}
+
+do_part_check() {
+	local emmc_parts="1 2 3 4"
+	local part_valid="1"
+
+	# Check if the block devices exist
+	for num in ${emmc_parts}; do
+		[[ ! -b ${emmc_dev}p${num} ]] && part_valid="0"
+	done
+
+	# If partitions are missing create a new partition table
+	if [ "$part_valid" != "1" ]; then
+		printf "Invalid partition table, creating a new one\n"
+		printf "o\nn\np\n1\n\n+256M\nn\np\n2\n\n+256M\nn\np\n3\n\n+1536M\nn\np\n\n\nw\n" | fdisk -W always $emmc_dev  > /dev/null 2>&1
+
+		# Format the /misc part right away as we will need it for the firmware
+		printf "Formating /misc partition, this make take a while..\n"
+		part_prep ${emmc_dev}p4
+		mkfs.f2fs -q -l misc ${emmc_dev}p4
+		[ $? -eq 0 ] && printf "/misc partition formated successfully\n" || printf "/misc partition formatting failed\n"
+
+		do_initial_setup
+	else
+		printf "Partition table looks ok\n"
+	fi
+}
+
+do_misc_prep() {
+	if [ ! "$(grep -wo /misc /proc/mounts)" ]; then
+		mkdir -p /misc
+		mount ${emmc_dev}p4 /misc
+
+		# If the mount fails, try to reformat partition
+		# Leaving possiblity for multiple iterations
+		if [ $? -ne 0 ]; then
+			printf "Error while mounting /misc, trying to reformat..\n"
+
+			format_count=0
+			while [ "$format_count" -lt "1" ]; do
+				part_prep ${emmc_dev}p4
+				mkfs.f2fs -q -l misc ${emmc_dev}p4
+				mount ${emmc_dev}p4 /misc
+				if [ $? -ne 0 ]; then
+					umount -l /misc
+					printf "Failed while mounting /misc\n"
+					format_count=$((format_count +1))
+				else
+					printf "Mounted /misc successfully\n"
+					break
+				fi
+			done
+		fi
+	fi
+}
+
+do_initial_setup() {
+	# Prepare /recovery parition
+	part_prep ${emmc_dev}p2
+	mkfs.ext4 -q ${emmc_dev}p2 | echo y &> /dev/null
+
+	# Prepare /boot partition
+	part_prep ${emmc_dev}p1
+	mkfs.ext4 -q ${emmc_dev}p1 | echo y &> /dev/null
+
+	# Prepare /root partition
+	printf "Formating /root partition, this may take a while..\n"
+	part_prep ${emmc_dev}p3
+	mkfs.f2fs -q -l rootfs ${emmc_dev}p3
+	[ $? -eq 0 ] && printf "/root partition reformated\n"
+}
+
+do_regular_upgrade() {
+	# Clean /boot partition - mfks.ext4 is not available in chroot
+	[ "$(grep -wo /boot /proc/mounts)" ] && umount /boot
+	mkdir -p /tmp/boot
+	mount ${emmc_dev}p1 /tmp/boot
+	rm -rf /tmp/boot/*
+
+	# Clean /root partition - mkfs.f2fs is not available in chroot
+	[ "$(grep -wo /dev/root /proc/mounts)" ] && umount /
+	mkdir -p /tmp/rootpart
+	mount ${emmc_dev}p3 /tmp/rootpart
+	rm -rf /tmp/rootpart/*
+}
+
+platform_do_upgrade_uDPU() {
+	# Prepare and extract firmware on /misc partition
+	do_misc_prep
+
+	[ -f "/misc/firmware" ] && rm -r /misc/firmware
+	mkdir -p /misc/firmware
+	tar xzf "$1" -C /misc/firmware/
+
+	do_regular_upgrade
+
+	printf "Updating /boot partition\n"
+	tar xzf /misc/firmware/boot.tgz -C /tmp/boot
+	[ $? -eq 0 ] && printf "/boot partition updated successfully\n" || printf "/boot partition update failed\n"
+	sync
+
+	printf "Updating /root partition\n"
+	tar xzf /misc/firmware/rootfs.tgz -C /tmp/rootpart
+	[ $? -eq 0 ] && printf "/root partition updated successfully\n" || printf "/root partition update failed\n"
+	sync
+
+	# Saving configuration files over sysupgrade
+	platform_copy_config_uDPU
+
+	# Remove tmp mounts
+	tmp_parts=$(grep "${emmc_dev}" /proc/mounts | awk '{print $2}')
+	for part in ${tmp_parts}; do
+		umount $part
+		# Force umount is necessary
+		[ "$(grep "${part}" /proc/mounts)" ] && umount -l $part
+	done
+
+	# Sysupgrade complains about /tmp and /dev, so we can detach them here
+	umount -l /tmp
+	umount -l /dev
+}
+
+platform_copy_config_uDPU() {
+	# Config is saved on the /misc partition and copied on the rootfs after the reboot
+	if [ -f "/tmp/sysupgrade.tgz" ]; then
+		cp -f /tmp/sysupgrade.tgz /misc
+		sync
+	fi
+}

target/linux/mvebu/image/Makefile

@@ -68,6 +68,15 @@ define Build/omnia-medkit-initramfs
 		--file=$@ -C $(dir $(IMAGE_KERNEL))boot/ .
 endef
 
+define Build/uDPU-firmware
+	(rm -fR $@-fw; mkdir -p $@-fw)
+	$(CP) $(BIN_DIR)/$(IMAGE_PREFIX)-initramfs.itb $@-fw/recovery.itb
+	$(CP) $@-boot.scr $@-fw/boot.scr
+	(cd $(TARGET_DIR); $(TAR) -cvzf $@-fw/rootfs.tgz .)
+	(cd $@.boot; $(TAR) -cvzf $@-fw/boot.tgz .)
+	(cd $@-fw; $(TAR) -cvzf $(KDIR_TMP)/$(IMAGE_PREFIX)-firmware.tgz .)
+endef
+
 define Device/Default
   PROFILES := Default
   BOARD_NAME = $$(DEVICE_DTS)

target/linux/mvebu/image/cortex-a53.mk

@@ -35,7 +35,7 @@ define Device/marvell_armada-3720-db
 endef
 TARGET_DEVICES += marvell_armada-3720-db
 
-define Device/methode_uDPU
+define Device/methode_udpu
   $(call Device/Default-arm64)
   DEVICE_TITLE := Methode micro-DPU (uDPU)
   DEVICE_DTS := armada-3720-uDPU
@@ -44,8 +44,12 @@ define Device/methode_uDPU
   KERNEL_INITRAMFS_SUFFIX := .itb
   DEVICE_PACKAGES := f2fs-tools e2fsprogs fdisk ethtool kmod-usb2 kmod-usb3 \
 			kmod-e100 kmod-e1000 kmod-e1000e kmod-igb kmod-ixgbevf \
-			kmod-mdio-gpio kmod-switch-mvsw61xx
+			kmod-mdio-gpio kmod-switch-mvsw61xx kmod-i2c-pxa
+  IMAGE_NAME = $$(IMAGE_PREFIX)-$$(2)
+  IMAGES := firmware.tgz
+  IMAGE/firmware.tgz := boot-scr | boot-img-ext4 | uDPU-firmware | append-metadata
+  BOOT_SCRIPT := udpu
 endef
-TARGET_DEVICES += methode_uDPU
+TARGET_DEVICES += methode_udpu
 
 endif

target/linux/mvebu/image/udpu.bootscript

@@ -0,0 +1,38 @@
+# Bootscript for Methode uDPU device
+# Device and variables may vary between different revisions
+# of device, so we need to make sure everything is set correctly.
+
+# Set the LED's correctly
+gpio clear 12; gpio clear 40; gpio clear 45;
+
+# Find eMMC device,
+if mmc dev 0; then
+	setenv mmcdev 0
+	setenv rootdev 'root=/dev/mmcblk0p3'
+elif mmc dev 1; then
+	setenv mmcdev 1
+	setenv rootdev 'root=/dev/mmcblk1p3'
+fi
+
+# Set the variables if necessary
+if test ${kernel_addr_r}; then
+	setenv kernel_addr_r 0x5000000
+fi
+
+if test ${fdt_add_r}; then
+	setenv fdt_addr_r 0x4f00000
+fi
+
+setenv console 'console=ttyMV0,115200 earlycon=ar3700_uart,0xd0012000'
+setenv bootargs ${console} $rootdev rw rootwait
+
+load mmc ${mmcdev}:1 ${fdt_addr_r} @DTB@.dtb
+load mmc ${mmcdev}:1 ${kernel_addr_r} Image
+
+booti ${kernel_addr_r} - ${fdt_addr_r}
+
+# If the boot command fails, fallback to recovery image
+echo '-- Boot failed, falling back to the recovery image --'
+setenv bootargs $console
+load mmc ${mmcdev}:2 ${kernel_addr_r} recovery.itb
+bootm ${kernel_addr_r}