ipq40xx: add support for AVM FRITZ!Repeater 3000
Hardware -------- CPU: Qualcomm IPQ4019 RAM: 256M (NANYA NT5CC128M16JR-EK) FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI) ETH: Qualcomm QCA8072 WiFi2: IPQ4019 2T2R 2SS b/g/n WiFi5: IPQ4019 2T2R 2SS n/ac WiFi5: QCA9984 4T4R 4SS n/ac LED: - Connect green/blue/red - Power green BTN: WPS/Connect UART: 115200n8 3.3V VCC - RX - TX - GND (Square is VCC) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz3000' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ3000.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz3000.bin uboot0 > mtd write /path/to/uboot-fritz3000.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
This commit is contained in:
parent
5389db72e3
commit
148d29d47b
@ -25,6 +25,11 @@ define U-Boot/Default
|
||||
UBOOT_IMAGE:=uboot-$(1).bin
|
||||
endef
|
||||
|
||||
define U-Boot/fritz3000
|
||||
NAME:=FritzRepeater 3000
|
||||
BUILD_DEVICES:=avm_fritzrepeater-3000
|
||||
endef
|
||||
|
||||
define U-Boot/fritz4040
|
||||
NAME:=FritzBox 4040
|
||||
BUILD_DEVICES:=avm_fritzbox-4040
|
||||
@ -61,6 +66,6 @@ define Package/u-boot/install
|
||||
$(INSTALL_BIN) $(PKG_BUILD_DIR)/upload-to-f4040.sh $(1)/
|
||||
endef
|
||||
|
||||
UBOOT_TARGETS := fritz4040 fritz7530
|
||||
UBOOT_TARGETS := fritz3000 fritz4040 fritz7530
|
||||
|
||||
$(eval $(call BuildPackage/U-Boot))
|
||||
|
@ -18,7 +18,7 @@ endef
|
||||
# Please send a mail with your device-specific board files upstream.
|
||||
# You can find instructions and examples on the linux-wireless wiki:
|
||||
# <https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles>
|
||||
ALLWIFIBOARDS:=alfa-network_ap120c-ac asus_map-ac2200 avm_fritzbox-7530 engenius_eap1300 linksys_ea6350v3 qxwlan_e2600ac
|
||||
ALLWIFIBOARDS:=alfa-network_ap120c-ac asus_map-ac2200 avm_fritzbox-7530 avm_fritzrepeater-3000 engenius_eap1300 linksys_ea6350v3 qxwlan_e2600ac
|
||||
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
|
||||
|
||||
define Package/ipq-wifi-default
|
||||
@ -57,6 +57,7 @@ $(eval $(call generate-ipq-wifi-package,alfa-network_ap120c-ac,board-alfa-networ
|
||||
$(eval $(call generate-ipq-wifi-package,asus_map-ac2200,board-map-ac2200.bin,ASUS MAP-AC2200))
|
||||
$(eval $(call generate-ipq-wifi-package,engenius_eap1300,board-engenius_eap1300.bin,EnGenius EAP1300))
|
||||
$(eval $(call generate-ipq-wifi-package,avm_fritzbox-7530,board-avm_fritzbox-7530.bin,AVM FRITZ!Box 7530))
|
||||
$(eval $(call generate-ipq-wifi-package,avm_fritzrepeater-3000,board-avm_fritzrepeater-3000.bin,AVM FRITZ!Repeater 3000))
|
||||
$(eval $(call generate-ipq-wifi-package,linksys_ea6350v3,board-linksys_ea6350v3.bin,Linksys EA6350v3))
|
||||
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,board-qxwlan-e2600ac.bin,Qxwlan E2600AC))
|
||||
|
||||
|
BIN
package/firmware/ipq-wifi/board-avm_fritzrepeater-3000.bin
Normal file
BIN
package/firmware/ipq-wifi/board-avm_fritzrepeater-3000.bin
Normal file
Binary file not shown.
@ -37,6 +37,7 @@ ipq40xx_setup_interfaces()
|
||||
ucidef_add_switch "switch0" \
|
||||
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
|
||||
;;
|
||||
avm,fritzrepeater-3000|\
|
||||
compex,wpj428)
|
||||
ucidef_set_interface_lan "eth0 eth1"
|
||||
;;
|
||||
|
@ -111,6 +111,10 @@ case "$FIRMWARE" in
|
||||
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
||||
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
||||
;;
|
||||
avm,fritzrepeater-3000)
|
||||
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
|
||||
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
|
||||
;;
|
||||
openmesh,a62)
|
||||
ath10kcal_extract "0:ART" 36864 12064
|
||||
;;
|
||||
@ -135,7 +139,8 @@ case "$FIRMWARE" in
|
||||
avm,fritzbox-4040)
|
||||
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
|
||||
;;
|
||||
avm,fritzbox-7530)
|
||||
avm,fritzbox-7530 |\
|
||||
avm,fritzrepeater-3000)
|
||||
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
|
||||
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
|
||||
;;
|
||||
@ -183,7 +188,8 @@ case "$FIRMWARE" in
|
||||
avm,fritzbox-4040)
|
||||
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
|
||||
;;
|
||||
avm,fritzbox-7530)
|
||||
avm,fritzbox-7530 |\
|
||||
avm,fritzrepeater-3000)
|
||||
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
|
||||
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
|
||||
;;
|
||||
|
@ -49,6 +49,7 @@ platform_do_upgrade() {
|
||||
8dev,jalapeno |\
|
||||
alfa-network,ap120c-ac |\
|
||||
avm,fritzbox-7530 |\
|
||||
avm,fritzrepeater-3000|\
|
||||
qxwlan,e2600ac-c2)
|
||||
nand_do_upgrade "$ARGV"
|
||||
;;
|
||||
|
@ -0,0 +1,260 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "AVM FRITZ!Repeater 3000";
|
||||
compatible = "avm,fritzrepeater-3000";
|
||||
|
||||
aliases {
|
||||
led-boot = &power_led;
|
||||
led-failsafe = &power_led;
|
||||
led-running = &power_led;
|
||||
led-upgrade = &power_led;
|
||||
};
|
||||
|
||||
soc {
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
|
||||
switch_lan_bmp = <0x10>;
|
||||
switch_wan_bmp = <0x20>;
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
key {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
connect {
|
||||
label = "Connect";
|
||||
gpios = <&tlmm 10 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
connect_red {
|
||||
label = "fritzwlan-3000:red:connect";
|
||||
gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
connect_green {
|
||||
label = "fritzwlan-3000:green:connect";
|
||||
gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
connect_blue {
|
||||
label = "fritzwlan-3000:blue:connect";
|
||||
gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
power_led: power {
|
||||
label = "fritzwlan-3000:green:power";
|
||||
gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
serial_0_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio16", "gpio17";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
nand_pins: nand_pins {
|
||||
pullups {
|
||||
pins = "gpio53", "gpio58", "gpio59";
|
||||
function = "qpic";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
pulldowns {
|
||||
pins = "gpio54", "gpio55", "gpio56",
|
||||
"gpio57", "gpio60", "gpio61",
|
||||
"gpio62", "gpio63", "gpio64",
|
||||
"gpio65", "gpio66", "gpio67",
|
||||
"gpio68", "gpio69";
|
||||
function = "qpic";
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nand {
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "SBL1";
|
||||
reg = <0x000000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "MIBIB";
|
||||
reg = <0x080000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "QSEE";
|
||||
reg = <0x100000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
label = "CDT";
|
||||
reg = <0x180000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1c0000 {
|
||||
label = "QSEE_B";
|
||||
reg = <0x1c0000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@240000 {
|
||||
label = "urlader0";
|
||||
reg = <0x240000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@280000 {
|
||||
label = "urlader1";
|
||||
reg = <0x280000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@2c0000 {
|
||||
label = "nand-tffs";
|
||||
reg = <0x2c0000 0x840000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@b00000 {
|
||||
/* 'kernel1' in AVM firmware */
|
||||
label = "uboot0";
|
||||
reg = <0xb00000 0x400000>;
|
||||
};
|
||||
|
||||
partition@f00000 {
|
||||
/* 'kernel2' in AVM firmware */
|
||||
label = "uboot1";
|
||||
reg = <0xf00000 0x400000>;
|
||||
};
|
||||
|
||||
partition@1300000 {
|
||||
label = "ubi";
|
||||
reg = <0x1300000 0x6d00000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
pinctrl-0 = <&serial_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
/* BDFs are identical for the FRITZ!Box 7530 and the FRITZ!Repeater 3000 */
|
||||
qcom,ath10k-calibration-variant = "AVM-FRITZRepeater-3000";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
ieee80211-freq-limit = <5170000 5350000>;
|
||||
/* BDFs are identical for the FRITZ!Box 7530 and the FRITZ!Repeater 3000 */
|
||||
qcom,ath10k-calibration-variant = "AVM-FRITZRepeater-3000";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
|
||||
perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
|
||||
wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
|
||||
|
||||
bridge@0,0 {
|
||||
reg = <0x00000000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
wifi@1,0 {
|
||||
/* QCA9984 */
|
||||
compatible = "qcom,ath10k";
|
||||
status = "okay";
|
||||
reg = <0x00010000 0 0 0 0>;
|
||||
ieee80211-freq-limit = <5470000 5875000>;
|
||||
/* Uses the reference BDF */
|
||||
};
|
||||
};
|
||||
};
|
@ -0,0 +1,264 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "AVM FRITZ!Repeater 3000";
|
||||
compatible = "avm,fritzrepeater-3000";
|
||||
|
||||
aliases {
|
||||
led-boot = &power_led;
|
||||
led-failsafe = &power_led;
|
||||
led-running = &power_led;
|
||||
led-upgrade = &power_led;
|
||||
};
|
||||
|
||||
soc {
|
||||
rng@22000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
|
||||
switch_lan_bmp = <0x10>;
|
||||
switch_wan_bmp = <0x20>;
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
key {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
connect {
|
||||
label = "Connect";
|
||||
gpios = <&tlmm 10 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
connect_red {
|
||||
label = "fritzwlan-3000:red:connect";
|
||||
gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
connect_green {
|
||||
label = "fritzwlan-3000:green:connect";
|
||||
gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
connect_blue {
|
||||
label = "fritzwlan-3000:blue:connect";
|
||||
gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
power_led: power {
|
||||
label = "fritzwlan-3000:green:power";
|
||||
gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
serial_0_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio16", "gpio17";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
nand_pins: nand_pins {
|
||||
pullups {
|
||||
pins = "gpio53", "gpio58", "gpio59";
|
||||
function = "qpic";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
pulldowns {
|
||||
pins = "gpio54", "gpio55", "gpio56",
|
||||
"gpio57", "gpio60", "gpio61",
|
||||
"gpio62", "gpio63", "gpio64",
|
||||
"gpio65", "gpio66", "gpio67",
|
||||
"gpio68", "gpio69";
|
||||
function = "qpic";
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nand {
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "SBL1";
|
||||
reg = <0x000000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "MIBIB";
|
||||
reg = <0x080000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "QSEE";
|
||||
reg = <0x100000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
label = "CDT";
|
||||
reg = <0x180000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1c0000 {
|
||||
label = "QSEE_B";
|
||||
reg = <0x1c0000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@240000 {
|
||||
label = "urlader0";
|
||||
reg = <0x240000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@280000 {
|
||||
label = "urlader1";
|
||||
reg = <0x280000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@2c0000 {
|
||||
label = "nand-tffs";
|
||||
reg = <0x2c0000 0x840000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@b00000 {
|
||||
/* 'kernel1' in AVM firmware */
|
||||
label = "uboot0";
|
||||
reg = <0xb00000 0x400000>;
|
||||
};
|
||||
|
||||
partition@f00000 {
|
||||
/* 'kernel2' in AVM firmware */
|
||||
label = "uboot1";
|
||||
reg = <0xf00000 0x400000>;
|
||||
};
|
||||
|
||||
partition@1300000 {
|
||||
label = "ubi";
|
||||
reg = <0x1300000 0x6d00000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
pinctrl-0 = <&serial_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
/* BDFs are identical for the FRITZ!Box 7530 and the FRITZ!Repeater 3000 */
|
||||
qcom,ath10k-calibration-variant = "AVM-FRITZRepeater-3000";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
ieee80211-freq-limit = <5170000 5350000>;
|
||||
/* BDFs are identical for the FRITZ!Box 7530 and the FRITZ!Repeater 3000 */
|
||||
qcom,ath10k-calibration-variant = "AVM-FRITZRepeater-3000";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
|
||||
perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
|
||||
wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
|
||||
|
||||
bridge@0,0 {
|
||||
reg = <0x00000000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
wifi@1,0 {
|
||||
/* QCA9984 */
|
||||
compatible = "qcom,ath10k";
|
||||
status = "okay";
|
||||
reg = <0x00010000 0 0 0 0>;
|
||||
ieee80211-freq-limit = <5470000 5875000>;
|
||||
/* Uses the reference BDF */
|
||||
};
|
||||
};
|
||||
};
|
@ -130,6 +130,15 @@ define Device/avm_fritzbox-7530
|
||||
endef
|
||||
TARGET_DEVICES += avm_fritzbox-7530
|
||||
|
||||
define Device/avm_fritzrepeater-3000
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_DTS := qcom-ipq4019-fritzrepeater-3000
|
||||
DEVICE_TITLE := AVM Fritz!Repeater 3000
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct fritz-caldata fritz-tffs-nand ipq-wifi-avm_fritzrepeater-3000
|
||||
IMAGES := sysupgrade.bin
|
||||
endef
|
||||
TARGET_DEVICES += avm_fritzrepeater-3000
|
||||
|
||||
define Device/compex_wpj428
|
||||
$(call Device/FitImage)
|
||||
DEVICE_DTS := qcom-ipq4028-wpj428
|
||||
|
@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
|
||||
--- a/arch/arm/boot/dts/Makefile
|
||||
+++ b/arch/arm/boot/dts/Makefile
|
||||
@@ -697,7 +697,27 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
@@ -697,7 +697,28 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
qcom-apq8074-dragonboard.dtb \
|
||||
qcom-apq8084-ifc6540.dtb \
|
||||
qcom-apq8084-mtp.dtb \
|
||||
@ -29,6 +29,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
+ qcom-ipq4019-a62.dtb \
|
||||
+ qcom-ipq4019-ap.dk04.1-c1.dtb \
|
||||
+ qcom-ipq4019-fritzbox-7530.dtb \
|
||||
+ qcom-ipq4019-fritzrepeater-3000.dtb \
|
||||
+ qcom-ipq4019-map-ac2200.dtb \
|
||||
+ qcom-ipq4019-qxwlan-e2600ac-c1.dtb \
|
||||
+ qcom-ipq4019-qxwlan-e2600ac-c2.dtb \
|
||||
|
@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
|
||||
--- a/arch/arm/boot/dts/Makefile
|
||||
+++ b/arch/arm/boot/dts/Makefile
|
||||
@@ -785,11 +785,30 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
@@ -785,11 +785,31 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
qcom-apq8074-dragonboard.dtb \
|
||||
qcom-apq8084-ifc6540.dtb \
|
||||
qcom-apq8084-mtp.dtb \
|
||||
@ -32,6 +32,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
qcom-ipq4019-ap.dk07.1-c2.dtb \
|
||||
+ qcom-ipq4019-a62.dtb \
|
||||
+ qcom-ipq4019-fritzbox-7530.dtb \
|
||||
+ qcom-ipq4019-fritzrepeater-3000.dtb \
|
||||
+ qcom-ipq4019-map-ac2200.dtb \
|
||||
+ qcom-ipq4019-qxwlan-e2600ac-c1.dtb \
|
||||
+ qcom-ipq4019-qxwlan-e2600ac-c2.dtb \
|
||||
|
Loading…
Reference in New Issue
Block a user