lantiq: add support for FritzBox 7312
The FritzBox 7312 is also known as 1&1 WLAN-MODEM. The device is almost the same as FB7330, but only one ETH-Port and no USB. Hardware SoC: Lantiq Xway ARX188 PSB 50812 EL RAM: 64MB DDR1 (Zentel A4S12D40FTP-G5) Ethernet: Atheros 8030 Wireless: Atheros AR9227 b/g/n 2x2 DSL: Lantiq ADSL2+ DECT: Dialog SC14441 Buttons: WiFi, DECT LEDs: Power/DSL, Fon, DECT, WLAN, Info LEDs Power: GPIO#44 (active low) Internet: GPIO#47 (active low) DECT: GPIO#38 (active low) WLAN: GPIO#37 (active low) Info: GPIO#35 (active low) The Fon LED is labeled as internet in avm gpl sources. Buttons WLAN: GPIO#1 (active low) DECT: GPIO#2 (active low) Phy GPIO#03: 25 MHz GPIO#34: Reset (active low) GPIO#39: Int GPIO#42: MII MDIO GPIO#43: MII MDC PCIe GPIO#21: reset (active low) Installation: To install OpenWrt via Eva bootloader, within the first seconds after power on a ftp connection need to be established to the FRITZ!Box at 192.168.178.1 and the the following ftp commands need to be run: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put /path/to/openwrt-lantiq-xway-avm_fritz7312-squashfs-sysupgrade.bin mtd1 ftp> quote REBOOT Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
This commit is contained in:
Johann Neuhauser
Mathias Kresin
parent
f2f7802148
commit
02d53e6a21
@ -144,6 +144,7 @@ avm,fritz3370-rev2-micron)
|
||||
"0:lan:3" "1:lan:4" "2:lan:2" "4:lan:1" "6t@eth0"
|
||||
;;
|
||||
|
||||
avm,fritz7312|\
|
||||
avm,fritz7320)
|
||||
annex="b"
|
||||
wan_mac=$(macaddr_add "$(mtd_get_mac_binary urlader 2705)" 1)
|
||||
|
||||
@ -160,7 +160,7 @@ case "$FIRMWARE" in
|
||||
avm,fritz3370-rev2-micron)
|
||||
ath9k_eeprom_extract_reverse "urlader" 5441 1088
|
||||
;;
|
||||
avm,fritz7320|avm,fritz7360sl)
|
||||
avm,fritz7312|avm,fritz7320|avm,fritz7360sl)
|
||||
ath9k_eeprom_extract "urlader" 2437 0
|
||||
;;
|
||||
tplink,tdw8970|tplink,tdw8980)
|
||||
|
||||
181
target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7312.dts
Normal file
181
target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7312.dts
Normal file
@ -0,0 +1,181 @@
|
||||
/dts-v1/;
|
||||
|
||||
#include "ar9.dtsi"
|
||||
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
compatible = "avm,fritz7312", "lantiq,xway", "lantiq,ar9";
|
||||
model = "FritzBox 7312 (1&1 WLAN-MODEM)";
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyLTQ0,115200";
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &power;
|
||||
led-failsafe = &power;
|
||||
led-running = &power;
|
||||
|
||||
led-internet = &info_green;
|
||||
led-dsl = &power;
|
||||
led-wifi = &wlan;
|
||||
};
|
||||
|
||||
memory@0 {
|
||||
reg = <0x0 0x4000000>;
|
||||
};
|
||||
|
||||
gpio-keys-polled {
|
||||
compatible = "gpio-keys-polled";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
poll-interval = <100>;
|
||||
|
||||
wlan {
|
||||
label = "wlan";
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RFKILL>;
|
||||
};
|
||||
dect {
|
||||
label = "dect";
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_PHONE>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
power: power {
|
||||
label = "fritz7312:green:power";
|
||||
gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
|
||||
default-state = "keep";
|
||||
};
|
||||
voice {
|
||||
label = "fritz7312:green:fon";
|
||||
gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
dect {
|
||||
label = "fritz7312:green:dect";
|
||||
gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
wlan: wlan {
|
||||
label = "fritz7312:green:wlan";
|
||||
gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
info_green: info_green {
|
||||
label = "fritz7312:green:info";
|
||||
gpios = <&gpio 35 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gpio {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&state_default>;
|
||||
|
||||
state_default: pinmux {
|
||||
pci {
|
||||
lantiq,groups = "gnt1", "req1", "req2", "req4", "gnt2", "gnt3", "gnt4";
|
||||
lantiq,function = "pci";
|
||||
};
|
||||
pci-in {
|
||||
lantiq,groups = "req1", "req2", "req4";
|
||||
lantiq,output = <0>;
|
||||
lantiq,open-drain = <1>;
|
||||
lantiq,pull = <2>;
|
||||
};
|
||||
pci-out {
|
||||
lantiq,groups = "gnt1", "gnt2", "gnt3", "gnt4";
|
||||
lantiq,output = <1>;
|
||||
lantiq,pull = <0>;
|
||||
};
|
||||
ar8030-intr {
|
||||
lantiq,groups = "exin3";
|
||||
lantiq,function = "exin";
|
||||
lantiq,pull = <2>;
|
||||
lantiq,output = <0>;
|
||||
};
|
||||
ar8030-clk {
|
||||
lantiq,groups = "clkout2";
|
||||
lantiq,output = <1>;
|
||||
lantiq,open-drain;
|
||||
};
|
||||
ar8030-rst {
|
||||
lantiq,pins = "io34";
|
||||
lantiq,output = <1>;
|
||||
lantiq,pull = <2>;
|
||||
lantiq,open-drain;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gsw {
|
||||
phy-mode = "rmii";
|
||||
phy-handle = <&phy0>;
|
||||
mtd-mac-address = <&ath9k_cal 0xa91>;
|
||||
mtd-mac-address-increment = <(-2)>;
|
||||
|
||||
mdio-bus {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0>;
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
reset-gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&localbus {
|
||||
nor@0 {
|
||||
compatible = "lantiq,nor";
|
||||
bank-width = <2>;
|
||||
reg = <0 0x0 0x1000000>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
ath9k_cal: partition@0 {
|
||||
label = "urlader";
|
||||
reg = <0x00000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
label = "firmware";
|
||||
reg = <0x20000 0xf60000>;
|
||||
};
|
||||
|
||||
partition@f80000 {
|
||||
label = "tffs (1)";
|
||||
reg = <0xf80000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@fc0000 {
|
||||
label = "tffs (2)";
|
||||
reg = <0xfc0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pci0 {
|
||||
status = "okay";
|
||||
req-mask = <0xf>;
|
||||
gpio-reset = <&gpio 21 GPIO_ACTIVE_LOW>;
|
||||
|
||||
wifi@0,0 {
|
||||
compatible = "pci0,0";
|
||||
reg = <0x7000 0 0 0 0>;
|
||||
qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */
|
||||
};
|
||||
};
|
||||
@ -485,6 +485,19 @@ define Device/buffalo_wbmr-hp-g300h-b
|
||||
endef
|
||||
TARGET_DEVICES += buffalo_wbmr-hp-g300h-b
|
||||
|
||||
define Device/avm_fritz7312
|
||||
$(Device/AVM)
|
||||
DEVICE_DTS := FRITZ7312
|
||||
IMAGE_SIZE := 15744k
|
||||
DEVICE_TITLE := 1&1 WLAN-MODEM - FRITZ7312
|
||||
DEVICE_PACKAGES := kmod-ath9k kmod-owl-loader wpad-mini \
|
||||
kmod-ltq-adsl-ar9-mei kmod-ltq-adsl-ar9 \
|
||||
kmod-ltq-adsl-ar9-fw-b kmod-ltq-atm-ar9 \
|
||||
ltq-adsl-app ppp-mod-pppoa \
|
||||
kmod-ltq-deu-ar9 -swconfig
|
||||
endef
|
||||
TARGET_DEVICES += avm_fritz7312
|
||||
|
||||
define Device/avm_fritz7320
|
||||
$(Device/AVM)
|
||||
DEVICE_DTS := FRITZ7320
|
||||
|
||||
@ -1,5 +1,6 @@
|
||||
CONFIG_ADM6996_PHY=y
|
||||
CONFIG_AR8216_PHY=y
|
||||
CONFIG_AT803X_PHY=y
|
||||
CONFIG_BLK_MQ_PCI=y
|
||||
CONFIG_CRC16=y
|
||||
CONFIG_CRYPTO_ACOMP2=y
|
||||
|
||||
Loading…
Reference in New Issue
Block a user