EljakimHerrewijnen/Openwrt
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
acbea54bc2
Openwrt/target/linux/realtek/dts/rtl8382_d-link_dgs-1210-28.dts

99 lines
1.9 KiB
Plaintext
Raw Normal View History

rtl838x: add support for D-Link DGS-1210-28 Hardware specification ---------------------- * RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz * 128MB DRAM * 32MB NOR Flash (MX25L25635E) * 24 x 10/100/1000BASE-T ports - Internal PHY with 8 ports (RTL8218B) - Two external PHYs with 8 ports each (RTL8218B) * 4 x Gigabit RJ45/SFP Combo ports - External PHY with 4 SFP ports (RTL8214FC) * Power LED * Reset button on front panel * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J6 UART pinout ----------- [oooo]J3 [o]ooo|J6 | ^ ||`------ GND | | |`------- RX | | `-------- TX | `---------- Vcc (3V3) | `------------------ J3 is power input connector nearby J6 UART Boot initramfs image from U-Boot -------------------------------- 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. Press CTRL+C keys to get into real U-Boot prompt 3. Init network with `rtk network on` command 4. Load image with `tftpboot 0x8f000000 openwrt-rtl838x-generic-d-link_dgs-1210-28-initramfs-kernel.bin` command 5. Boot the image with `bootm` command To install, upload the sysupgrade image to the OEM webpage or sysupgrade from the system running from initramfs image. It has been developed and tested on device with F1 revision. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-04 10:37:42 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "rtl8382_d-link_dgs-1210.dtsi"
/ {
compatible = "d-link,dgs-1210-28", "realtek,rtl838x-soc";
model = "D-Link DGS-1210-28";
};
&ethernet0 {
mdio: mdio-bus {
compatible = "realtek,rtl838x-mdio";
regmap = <&ethernet0>;
#address-cells = <1>;
#size-cells = <0>;
rtl838x: dts: use macros for phy and switch definitions It's quite more readable, saves some tedious copy&pasting, not so error prone etc. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-04 15:20:17 +00:00
EXTERNAL_PHY(0)
EXTERNAL_PHY(1)
EXTERNAL_PHY(2)
EXTERNAL_PHY(3)
EXTERNAL_PHY(4)
EXTERNAL_PHY(5)
EXTERNAL_PHY(6)
EXTERNAL_PHY(7)
rtl838x: add support for D-Link DGS-1210-28 Hardware specification ---------------------- * RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz * 128MB DRAM * 32MB NOR Flash (MX25L25635E) * 24 x 10/100/1000BASE-T ports - Internal PHY with 8 ports (RTL8218B) - Two external PHYs with 8 ports each (RTL8218B) * 4 x Gigabit RJ45/SFP Combo ports - External PHY with 4 SFP ports (RTL8214FC) * Power LED * Reset button on front panel * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J6 UART pinout ----------- [oooo]J3 [o]ooo|J6 | ^ ||`------ GND | | |`------- RX | | `-------- TX | `---------- Vcc (3V3) | `------------------ J3 is power input connector nearby J6 UART Boot initramfs image from U-Boot -------------------------------- 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. Press CTRL+C keys to get into real U-Boot prompt 3. Init network with `rtk network on` command 4. Load image with `tftpboot 0x8f000000 openwrt-rtl838x-generic-d-link_dgs-1210-28-initramfs-kernel.bin` command 5. Boot the image with `bootm` command To install, upload the sysupgrade image to the OEM webpage or sysupgrade from the system running from initramfs image. It has been developed and tested on device with F1 revision. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-04 10:37:42 +00:00
rtl838x: dts: use macros for phy and switch definitions It's quite more readable, saves some tedious copy&pasting, not so error prone etc. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-04 15:20:17 +00:00
INTERNAL_PHY(8)
INTERNAL_PHY(9)
INTERNAL_PHY(10)
INTERNAL_PHY(11)
INTERNAL_PHY(12)
INTERNAL_PHY(13)
INTERNAL_PHY(14)
INTERNAL_PHY(15)
rtl838x: add support for D-Link DGS-1210-28 Hardware specification ---------------------- * RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz * 128MB DRAM * 32MB NOR Flash (MX25L25635E) * 24 x 10/100/1000BASE-T ports - Internal PHY with 8 ports (RTL8218B) - Two external PHYs with 8 ports each (RTL8218B) * 4 x Gigabit RJ45/SFP Combo ports - External PHY with 4 SFP ports (RTL8214FC) * Power LED * Reset button on front panel * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J6 UART pinout ----------- [oooo]J3 [o]ooo|J6 | ^ ||`------ GND | | |`------- RX | | `-------- TX | `---------- Vcc (3V3) | `------------------ J3 is power input connector nearby J6 UART Boot initramfs image from U-Boot -------------------------------- 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. Press CTRL+C keys to get into real U-Boot prompt 3. Init network with `rtk network on` command 4. Load image with `tftpboot 0x8f000000 openwrt-rtl838x-generic-d-link_dgs-1210-28-initramfs-kernel.bin` command 5. Boot the image with `bootm` command To install, upload the sysupgrade image to the OEM webpage or sysupgrade from the system running from initramfs image. It has been developed and tested on device with F1 revision. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-04 10:37:42 +00:00
rtl838x: dts: use macros for phy and switch definitions It's quite more readable, saves some tedious copy&pasting, not so error prone etc. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-04 15:20:17 +00:00
EXTERNAL_PHY(16)
EXTERNAL_PHY(17)
EXTERNAL_PHY(18)
EXTERNAL_PHY(19)
EXTERNAL_PHY(20)
EXTERNAL_PHY(21)
EXTERNAL_PHY(22)
EXTERNAL_PHY(23)
rtl838x: add support for D-Link DGS-1210-28 Hardware specification ---------------------- * RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz * 128MB DRAM * 32MB NOR Flash (MX25L25635E) * 24 x 10/100/1000BASE-T ports - Internal PHY with 8 ports (RTL8218B) - Two external PHYs with 8 ports each (RTL8218B) * 4 x Gigabit RJ45/SFP Combo ports - External PHY with 4 SFP ports (RTL8214FC) * Power LED * Reset button on front panel * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J6 UART pinout ----------- [oooo]J3 [o]ooo|J6 | ^ ||`------ GND | | |`------- RX | | `-------- TX | `---------- Vcc (3V3) | `------------------ J3 is power input connector nearby J6 UART Boot initramfs image from U-Boot -------------------------------- 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. Press CTRL+C keys to get into real U-Boot prompt 3. Init network with `rtk network on` command 4. Load image with `tftpboot 0x8f000000 openwrt-rtl838x-generic-d-link_dgs-1210-28-initramfs-kernel.bin` command 5. Boot the image with `bootm` command To install, upload the sysupgrade image to the OEM webpage or sysupgrade from the system running from initramfs image. It has been developed and tested on device with F1 revision. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-04 10:37:42 +00:00
rtl838x: dts: use macros for phy and switch definitions It's quite more readable, saves some tedious copy&pasting, not so error prone etc. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-04 15:20:17 +00:00
EXTERNAL_SFP_PHY(24)
EXTERNAL_SFP_PHY(25)
EXTERNAL_SFP_PHY(26)
EXTERNAL_SFP_PHY(27)
rtl838x: add support for D-Link DGS-1210-28 Hardware specification ---------------------- * RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz * 128MB DRAM * 32MB NOR Flash (MX25L25635E) * 24 x 10/100/1000BASE-T ports - Internal PHY with 8 ports (RTL8218B) - Two external PHYs with 8 ports each (RTL8218B) * 4 x Gigabit RJ45/SFP Combo ports - External PHY with 4 SFP ports (RTL8214FC) * Power LED * Reset button on front panel * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J6 UART pinout ----------- [oooo]J3 [o]ooo|J6 | ^ ||`------ GND | | |`------- RX | | `-------- TX | `---------- Vcc (3V3) | `------------------ J3 is power input connector nearby J6 UART Boot initramfs image from U-Boot -------------------------------- 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. Press CTRL+C keys to get into real U-Boot prompt 3. Init network with `rtk network on` command 4. Load image with `tftpboot 0x8f000000 openwrt-rtl838x-generic-d-link_dgs-1210-28-initramfs-kernel.bin` command 5. Boot the image with `bootm` command To install, upload the sysupgrade image to the OEM webpage or sysupgrade from the system running from initramfs image. It has been developed and tested on device with F1 revision. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-04 10:37:42 +00:00
};
};
&switch0 {
ports {
#address-cells = <1>;
#size-cells = <0>;
rtl838x: dts: use macros for phy and switch definitions It's quite more readable, saves some tedious copy&pasting, not so error prone etc. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-04 15:20:17 +00:00
SWITCH_PORT(0, 1, qsgmii)
SWITCH_PORT(1, 2, qsgmii)
SWITCH_PORT(2, 3, qsgmii)
SWITCH_PORT(3, 4, qsgmii)
SWITCH_PORT(4, 5, qsgmii)
SWITCH_PORT(5, 6, qsgmii)
SWITCH_PORT(6, 7, qsgmii)
SWITCH_PORT(7, 8, qsgmii)
SWITCH_PORT(8, 9, internal)
SWITCH_PORT(9, 10, internal)
SWITCH_PORT(10, 11, internal)
SWITCH_PORT(11, 12, internal)
SWITCH_PORT(12, 13, internal)
SWITCH_PORT(13, 14, internal)
SWITCH_PORT(14, 15, internal)
SWITCH_PORT(15, 16, internal)
SWITCH_PORT(16, 17, qsgmii)
SWITCH_PORT(17, 18, qsgmii)
SWITCH_PORT(18, 19, qsgmii)
SWITCH_PORT(19, 20, qsgmii)
SWITCH_PORT(20, 21, qsgmii)
SWITCH_PORT(21, 22, qsgmii)
SWITCH_PORT(22, 23, qsgmii)
SWITCH_PORT(23, 24, qsgmii)
SWITCH_PORT(24, 25, qsgmii)
SWITCH_PORT(25, 26, qsgmii)
SWITCH_PORT(26, 27, qsgmii)
SWITCH_PORT(27, 28, qsgmii)
rtl838x: add support for D-Link DGS-1210-28 Hardware specification ---------------------- * RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz * 128MB DRAM * 32MB NOR Flash (MX25L25635E) * 24 x 10/100/1000BASE-T ports - Internal PHY with 8 ports (RTL8218B) - Two external PHYs with 8 ports each (RTL8218B) * 4 x Gigabit RJ45/SFP Combo ports - External PHY with 4 SFP ports (RTL8214FC) * Power LED * Reset button on front panel * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J6 UART pinout ----------- [oooo]J3 [o]ooo|J6 | ^ ||`------ GND | | |`------- RX | | `-------- TX | `---------- Vcc (3V3) | `------------------ J3 is power input connector nearby J6 UART Boot initramfs image from U-Boot -------------------------------- 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. Press CTRL+C keys to get into real U-Boot prompt 3. Init network with `rtk network on` command 4. Load image with `tftpboot 0x8f000000 openwrt-rtl838x-generic-d-link_dgs-1210-28-initramfs-kernel.bin` command 5. Boot the image with `bootm` command To install, upload the sysupgrade image to the OEM webpage or sysupgrade from the system running from initramfs image. It has been developed and tested on device with F1 revision. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-04 10:37:42 +00:00
port@28 {
ethernet = <&ethernet0>;
reg = <28>;
phy-mode = "internal";
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
};
Reference in New Issue Copy Permalink