Openwrt/target/linux/mediatek/mt7622/config-5.10

440 lines
11 KiB
Plaintext
Raw Normal View History

CONFIG_64BIT=y
CONFIG_AHCI_MTK=y
CONFIG_ARCH_DMA_ADDR_T_64BIT=y
CONFIG_ARCH_KEEP_MEMBLOCK=y
CONFIG_ARCH_MEDIATEK=y
CONFIG_ARCH_MMAP_RND_BITS=18
CONFIG_ARCH_MMAP_RND_BITS_MAX=24
CONFIG_ARCH_MMAP_RND_BITS_MIN=18
CONFIG_ARCH_MMAP_RND_COMPAT_BITS=11
CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MIN=11
CONFIG_ARCH_PROC_KCORE_TEXT=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_ARCH_SPARSEMEM_DEFAULT=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_STACKWALK=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_ARM64=y
CONFIG_ARM64_4K_PAGES=y
# CONFIG_ARM64_CNP is not set
# CONFIG_ARM64_ERRATUM_1165522 is not set
# CONFIG_ARM64_ERRATUM_1286807 is not set
# CONFIG_ARM64_ERRATUM_1418040 is not set
CONFIG_ARM64_ERRATUM_843419=y
CONFIG_ARM64_ERRATUM_845719=y
CONFIG_ARM64_MODULE_PLTS=y
CONFIG_ARM64_PAGE_SHIFT=12
CONFIG_ARM64_PA_BITS=48
CONFIG_ARM64_PA_BITS_48=y
# CONFIG_ARM64_PTR_AUTH is not set
# CONFIG_ARM64_SVE is not set
# CONFIG_ARM64_SW_TTBR0_PAN is not set
CONFIG_ARM64_TAGGED_ADDR_ABI=y
CONFIG_ARM64_VA_BITS=39
CONFIG_ARM64_VA_BITS_39=y
# CONFIG_ARMV8_DEPRECATED is not set
CONFIG_ARM_AMBA=y
CONFIG_ARM_ARCH_TIMER=y
CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y
CONFIG_ARM_GIC=y
CONFIG_ARM_GIC_V2M=y
CONFIG_ARM_GIC_V3=y
CONFIG_ARM_GIC_V3_ITS=y
CONFIG_ARM_GIC_V3_ITS_PCI=y
CONFIG_ARM_MEDIATEK_CPUFREQ=y
CONFIG_ARM_PMU=y
CONFIG_ARM_PSCI_FW=y
CONFIG_ATA=y
CONFIG_AUDIT_ARCH_COMPAT_GENERIC=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_SD=y
CONFIG_BLK_MQ_PCI=y
CONFIG_BLK_PM=y
CONFIG_BLK_SCSI_REQUEST=y
CONFIG_BLOCK_COMPAT=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_BSD_PROCESS_ACCT_V3=y
# CONFIG_CAVIUM_TX2_ERRATUM_219 is not set
CONFIG_CLKDEV_LOOKUP=y
CONFIG_CLKSRC_MMIO=y
CONFIG_CLONE_BACKWARDS=y
CONFIG_COMMON_CLK=y
CONFIG_COMMON_CLK_MEDIATEK=y
CONFIG_COMMON_CLK_MT2712=y
# CONFIG_COMMON_CLK_MT2712_BDPSYS is not set
# CONFIG_COMMON_CLK_MT2712_IMGSYS is not set
# CONFIG_COMMON_CLK_MT2712_JPGDECSYS is not set
# CONFIG_COMMON_CLK_MT2712_MFGCFG is not set
# CONFIG_COMMON_CLK_MT2712_MMSYS is not set
# CONFIG_COMMON_CLK_MT2712_VDECSYS is not set
# CONFIG_COMMON_CLK_MT2712_VENCSYS is not set
# CONFIG_COMMON_CLK_MT6779 is not set
# CONFIG_COMMON_CLK_MT6797 is not set
CONFIG_COMMON_CLK_MT7622=y
CONFIG_COMMON_CLK_MT7622_AUDSYS=y
CONFIG_COMMON_CLK_MT7622_ETHSYS=y
CONFIG_COMMON_CLK_MT7622_HIFSYS=y
# CONFIG_COMMON_CLK_MT8173 is not set
CONFIG_COMMON_CLK_MT8183=y
# CONFIG_COMMON_CLK_MT8183_AUDIOSYS is not set
# CONFIG_COMMON_CLK_MT8183_CAMSYS is not set
# CONFIG_COMMON_CLK_MT8183_IMGSYS is not set
# CONFIG_COMMON_CLK_MT8183_IPU_ADL is not set
# CONFIG_COMMON_CLK_MT8183_IPU_CONN is not set
# CONFIG_COMMON_CLK_MT8183_IPU_CORE0 is not set
# CONFIG_COMMON_CLK_MT8183_IPU_CORE1 is not set
# CONFIG_COMMON_CLK_MT8183_MFGCFG is not set
# CONFIG_COMMON_CLK_MT8183_MMSYS is not set
# CONFIG_COMMON_CLK_MT8183_VDECSYS is not set
# CONFIG_COMMON_CLK_MT8183_VENCSYS is not set
CONFIG_COMMON_CLK_MT8516=y
# CONFIG_COMMON_CLK_MT8516_AUDSYS is not set
CONFIG_COMPAT=y
CONFIG_COMPAT_32BIT_TIME=y
CONFIG_COMPAT_BINFMT_ELF=y
CONFIG_COMPAT_NETLINK_MESSAGES=y
CONFIG_COMPAT_OLD_SIGACTION=y
CONFIG_CONSOLE_LOGLEVEL_DEFAULT=15
# CONFIG_CPUFREQ_DT is not set
CONFIG_CPU_FREQ=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_ATTR_SET=y
CONFIG_CPU_FREQ_GOV_COMMON=y
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=y
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=y
CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_STAT=y
CONFIG_CPU_RMAP=y
CONFIG_CPU_THERMAL=y
CONFIG_CRC16=y
CONFIG_CRYPTO_ACOMP2=y
CONFIG_CRYPTO_AEAD=y
CONFIG_CRYPTO_AEAD2=y
CONFIG_CRYPTO_CMAC=y
CONFIG_CRYPTO_DEFLATE=y
CONFIG_CRYPTO_DRBG=y
CONFIG_CRYPTO_DRBG_HMAC=y
CONFIG_CRYPTO_DRBG_MENU=y
CONFIG_CRYPTO_ECB=y
CONFIG_CRYPTO_ECC=y
CONFIG_CRYPTO_ECDH=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_HASH2=y
CONFIG_CRYPTO_HASH_INFO=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_JITTERENTROPY=y
CONFIG_CRYPTO_KPP=y
CONFIG_CRYPTO_KPP2=y
CONFIG_CRYPTO_LIB_SHA256=y
CONFIG_CRYPTO_LZO=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_MANAGER2=y
CONFIG_CRYPTO_NULL2=y
CONFIG_CRYPTO_RNG=y
CONFIG_CRYPTO_RNG2=y
CONFIG_CRYPTO_RNG_DEFAULT=y
CONFIG_CRYPTO_SHA256=y
CONFIG_DCACHE_WORD_ACCESS=y
CONFIG_DEBUG_MISC=y
CONFIG_DEVTMPFS=y
CONFIG_DEVTMPFS_MOUNT=y
CONFIG_DIMLIB=y
CONFIG_DMADEVICES=y
CONFIG_DMATEST=y
CONFIG_DMA_DIRECT_REMAP=y
CONFIG_DMA_ENGINE=y
CONFIG_DMA_ENGINE_RAID=y
CONFIG_DMA_OF=y
CONFIG_DMA_REMAP=y
CONFIG_DMA_VIRTUAL_CHANNELS=y
CONFIG_DTC=y
CONFIG_DYNAMIC_DEBUG=y
CONFIG_EDAC_SUPPORT=y
CONFIG_EINT_MTK=y
mediatek: rework support for BananaPi BPi-R64 **What's new** * Bring support for the Bananapi BPi-R64 to the level desirable for a nice hackable routerboard. * Use ARM Trusted Firmware A from source. (goodbye binary preloader) * Use Das U-Boot from source. (see previous commit) * Assemble SD-card image using OpenWrt image-commands. (no gen_sd_cruz_foo.sh added, this is not Raspbian) * Updated kernel options to support root filesystem. * Updated DTS to match OpenWrt LAN ports, known LEDs, buttons, ... * Detect root device, handle sysupgrade, config restore, ... * Wire up (known) LEDs and buttons in OpenWrt-fashion. * Build one set of images from SD-card and eMMC. * Hopefully provide a good example of how things can be done right from scratch. **Installation and images** * Have an empty SD-card at hand * Write stuff to the card, as root (card device is /dev/mmcblkX) - write header, gpt, bl2, atf, u-boot and recovery kernel: `cat *bpi-r64-boot-sdcard.img *bpi-r64-initramfs-recovery.fit > /dev/mmcblkX` - rescan partitions: `blockdev --rereadpt /dev/mmcblkX` - write main system to production partition: `cat *bpi-r64-squashfs-sysupgrade.fit > /dev/mmcblkXp5` * Installation to eMMC works using SD-card bootloader via TFTP When running OpenWrt of SD-card, issue this to trigger installation to eMMC: `fw_setenv bootcmd run emmc_init` Be prepared to serve the content of bin/targets/mediatek/mt7622 on TFTP server address 192.168.1.254. **What's missing** * The red LED is always on, probably a hardware bug. * AHCI (probably needs DTS changes) * Ship SD-card image ready with every needed for eMMC install. * The eMMC has a second, currently unused boot partition. This would be ideal to store the WiFi EEPROM and Ethernet MAC address(es). @sinovoip ideas? Thanks to Thomas Hühn @thuehn for providing the hardware! Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-27 14:17:09 +00:00
CONFIG_EXT4_FS=y
mediatek: add alternative UBI NAND layout for Linksys E8450 The vendor flash layout of the Linksys E8450 is problematic as it uses the SPI-NAND chip without any wear-leveling while at the same time wasting a lot of space for padding. Use an all-UBI layout instead, storing the kernel+dtb+squashfs in uImage.FIT standard format in UBI volume 'fit', the read-write overlay in UBI volume 'rootfs_data' as well as reduntant U-Boot environments 'ubootenv' and 'ubootenv2', and a 'recovery' kernel+dtb+initramfs uImage.FIT for dual-boot. ** WARNING ** THIS PROCEDURE CAN EASILY BRICK YOUR DEVICE PERMANENTLY IF NOT CARRIED OUT VERY CAREFULLY AND EXACTLY AS DESCRIBED! Step 0 * Configure your PC to have the static IPv4 address 192.168.1.254/24 * Provide bin/targets/mediatek/mt7622 via TFTP Now continue EITHER with step 1A or 1B, depending on your preference (and on having serial console wired up or not). Step 1A (Using the vendor web interface (or non-UBI OpenWrt install)) In order to update to the new bootloader and UBI-based firmware, use the web browser of your choice to open the routers web-interface accessible on http://192.168.1.1 * Navigate to 'Configuration' -> 'Administration' -> 'Firmware Upgrade' * Upload the file openwrt-mediatek-mt7622-linksys_e8450-ubi-initramfs-recovery.itb and proceed with the upgrade. * Once OpenWrt comes up, use SCP to upload the new bootloader files to /tmp on the router: *-mt7622-linksys_e8450-ubi-preloader.bin *-mt7622-linksys_e8450-ubi-bl31-uboot.fip * Connect via SSH as you will now need to replace the bootloader in the Flash. ssh root@192.168.1.1 (the usual warnings) * First of all, backup all the flash now: for mtd in /dev/mtdblock*; do dd if=$mtd of=/tmp/$(basename $mtd); done * Then use SCP to copy /tmp/mtdblock* from the router and keep them safe. You will need them should you ever want to return to the factory firmware! * Now flow the uploaded files: mtd -e /dev/mtd0 write /tmp/*linksys_e8450-ubi-preloader.bin /dev/mtd0 mtd -e /dev/mtd1 write /tmp/*linksys_e8450-ubi-bl31-uboot.fip /dev/mtd1 If and only if both writes look like the completed successfully reboot the router. Now continue with step 2. Step 1B (Using the vendor bootloader serial console) * Use the serial to backup all /dev/mtd* devices before using the stock firmware (you got root shell when connected to serial). * Then reboot and select 'U-Boot Console' in the boot menu. * Copy the following lines, one by one: tftpboot 0x40080000 openwrt-mediatek-mt7622-linksys_e8450-ubi-preloader.bin tftpboot 0x40100000 openwrt-mediatek-mt7622-linksys_e8450-ubi-bl31-uboot.fip nand erase 0x0 0x180000 nand write 0x40080000 0x0 0x180000 reset Now continue with step 2 Step 2 Once the new bootchain comes up, the loader will initialize UBI and the ubootenv volumes. It will then of course fail to find any bootable volume and hence resort to load kernel via TFTP from server 192.168.1.254 while giving itself the address 192.168.1.1 The requested file is called openwrt-mediatek-mt7622-linksys_e8450-ubi-initramfs-recovery.itb and your TFTP server should provide exactly that :) It will be written to UBI as recovery image and booted. You can then continue and flash the production OS image, either by using sysupgrade in the booted initramfs recovery OS, or by using the bootloader menu and TFTP. That's it. Go ahead and mess around with a bootchain built almost completely from source (only DRAM calibration blobs are fitted in bl2, and the irreplacable on-chip ROM loader remains, of course). And enjoy U-Boot built with many great features out-of-the-box. You can access the bootloader environment from within OpenWrt using the 'fw_printenv' and 'fw_setenv' commands. Don't be afraid, once you got the new bootchain installed the device should be fairly unbrickable (holding reset button before and during power-on resets things and allows reflashing recovery image via TFTP) Special thanks to @dvn0 (Devan Carpenter) for providing amazingly fast infra for test-builds, allowing for `make clean ; make -j$(nproc)` in less than two minutes :) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-09 23:07:42 +00:00
CONFIG_FIT_PARTITION=y
CONFIG_FIXED_PHY=y
CONFIG_FIX_EARLYCON_MEM=y
# CONFIG_FLATMEM_MANUAL is not set
CONFIG_FRAME_POINTER=y
CONFIG_F2FS_FS=y
# CONFIG_FUJITSU_ERRATUM_010001 is not set
CONFIG_FW_LOADER_PAGED_BUF=y
CONFIG_GENERIC_ALLOCATOR=y
CONFIG_GENERIC_ARCH_TOPOLOGY=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_BUG_RELATIVE_POINTERS=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
CONFIG_GENERIC_CPU_AUTOPROBE=y
CONFIG_GENERIC_CPU_VULNERABILITIES=y
CONFIG_GENERIC_CSUM=y
CONFIG_GENERIC_EARLY_IOREMAP=y
CONFIG_GENERIC_GETTIMEOFDAY=y
CONFIG_GENERIC_IDLE_POLL_SETUP=y
CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y
CONFIG_GENERIC_IRQ_MULTI_HANDLER=y
CONFIG_GENERIC_IRQ_SHOW=y
CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
CONFIG_GENERIC_MSI_IRQ=y
CONFIG_GENERIC_MSI_IRQ_DOMAIN=y
CONFIG_GENERIC_PCI_IOMAP=y
CONFIG_GENERIC_PHY=y
CONFIG_GENERIC_PINCONF=y
CONFIG_GENERIC_PINCTRL_GROUPS=y
CONFIG_GENERIC_PINMUX_FUNCTIONS=y
CONFIG_GENERIC_SCHED_CLOCK=y
CONFIG_GENERIC_SMP_IDLE_THREAD=y
CONFIG_GENERIC_STRNCPY_FROM_USER=y
CONFIG_GENERIC_STRNLEN_USER=y
CONFIG_GENERIC_TIME_VSYSCALL=y
CONFIG_GLOB=y
CONFIG_GPIOLIB=y
CONFIG_GRO_CELLS=y
CONFIG_HANDLE_DOMAIN_IRQ=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_HAS_DMA=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT_MAP=y
CONFIG_HOLES_IN_ZONE=y
CONFIG_HZ=250
CONFIG_HZ_250=y
CONFIG_ICPLUS_PHY=y
CONFIG_IIO=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_ILLEGAL_POINTER_VALUE=0xdead000000000000
CONFIG_INITRAMFS_SOURCE=""
CONFIG_IO_URING=y
CONFIG_IRQCHIP=y
CONFIG_IRQ_DOMAIN=y
CONFIG_IRQ_DOMAIN_HIERARCHY=y
CONFIG_IRQ_FORCED_THREADING=y
CONFIG_IRQ_TIME_ACCOUNTING=y
CONFIG_IRQ_WORK=y
CONFIG_JUMP_LABEL=y
CONFIG_LIBFDT=y
CONFIG_LLD_VERSION=0
CONFIG_LOCK_DEBUGGING_SUPPORT=y
CONFIG_LOCK_SPIN_ON_OWNER=y
CONFIG_LZO_COMPRESS=y
CONFIG_LZO_DECOMPRESS=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_MDIO_BUS=y
CONFIG_MDIO_DEVICE=y
CONFIG_MEDIATEK_MT6577_AUXADC=y
CONFIG_MEDIATEK_WATCHDOG=y
CONFIG_MEMFD_CREATE=y
CONFIG_MESSAGE_LOGLEVEL_DEFAULT=7
CONFIG_MFD_SYSCON=y
CONFIG_MIGRATION=y
CONFIG_MMC=y
CONFIG_MMC_BLOCK=y
CONFIG_MMC_CQHCI=y
CONFIG_MMC_MTK=y
# CONFIG_MMC_TIFM_SD is not set
CONFIG_MODULES_TREE_LOOKUP=y
CONFIG_MODULES_USE_ELF_RELA=y
CONFIG_MTD_NAND_CORE=y
CONFIG_MTD_NAND_ECC=y
CONFIG_MTD_NAND_ECC_SW_HAMMING=y
CONFIG_MTD_NAND_MTK=y
CONFIG_MTD_NAND_MTK_BMT=y
CONFIG_MTD_RAW_NAND=y
CONFIG_MTD_SPI_NAND=y
CONFIG_MTD_SPI_NOR=y
mediatek: add support for Buffalo WSR-2533DHP2 This adds support for the Buffalo WSR-2533DHP2. The device uses the Broadcom TRX image format with a special magic. To be able to boot the images or load them they have to be wrapped with different headers depending how it is loaded. There are multiple ways to install OpenWrt on this device. Boot ramdisk from U-Boot ---------------------------- This will load the image and not write it into the flash. 1. Stop boot menu with "space" key 2. Select "System Load Linux to SDRAM via TFTP." 3. Load this image: openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-initramfs-kernel.bin 4. The system boots the image Write to flash from U-Boot ----------------------------- This will load the image over tftp and directly write it into the flash. 1. Stop boot menu with "space" key 2. Select "System Load Linux Kernel then write to Flash via TFTP." 3. Load this image: openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory-uboot.bin 4. The system writes this image into the flash and boots into it. Write to flash from Web UI ----------------------------- This will load the image over over the Web UI and write it into the flash 1. Open the Web UI 2. Go to "管理" -> "ファームウェア更新" 3. Select "ローカルファイル指定" and click "更新実行" 4. Load this image: openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory.bin 5. The system writes this image into the flash and boots into it. Specifications ------------------- * SoC: MT7622 (4x4 2.4 GHz Wifi) * Wifi: MT7615 (4x4 5 GHz Wifi) * Flash: Winbond W29N01HZ 128MB SLC NAND * RAM 256MB * Ethernet: Realtek RTL8367S (5 x 1GBit/s, SoC via 2.5GBit/s) Co-Developed-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-07 17:36:16 +00:00
CONFIG_MTD_PARSER_TRX=y
CONFIG_MTD_SPLIT_FIRMWARE=y
CONFIG_MTD_SPLIT_FIT_FW=y
CONFIG_MTD_UBI=y
CONFIG_MTD_UBI_BEB_LIMIT=20
CONFIG_MTD_UBI_BLOCK=y
CONFIG_MTD_UBI_WL_THRESHOLD=4096
# CONFIG_MTK_CMDQ is not set
# CONFIG_MTK_CQDMA is not set
CONFIG_MTK_EFUSE=y
CONFIG_MTK_HSDMA=y
CONFIG_MTK_INFRACFG=y
CONFIG_MTK_PMIC_WRAP=y
CONFIG_MTK_SCPSYS=y
CONFIG_MTK_THERMAL=y
CONFIG_MTK_TIMER=y
# CONFIG_MTK_UART_APDMA is not set
CONFIG_MUTEX_SPIN_ON_OWNER=y
CONFIG_NEED_DMA_MAP_STATE=y
CONFIG_NEED_SG_DMA_LENGTH=y
CONFIG_NET_DEVLINK=y
CONFIG_NET_DSA=y
CONFIG_NET_DSA_MT7530=y
CONFIG_NET_DSA_TAG_MTK=y
CONFIG_NET_FLOW_LIMIT=y
CONFIG_NET_MEDIATEK_SOC=y
CONFIG_NET_SWITCHDEV=y
CONFIG_NET_VENDOR_MEDIATEK=y
CONFIG_NLS=y
CONFIG_NO_HZ_COMMON=y
CONFIG_NO_HZ_IDLE=y
CONFIG_NR_CPUS=2
CONFIG_NVMEM=y
CONFIG_NVMEM_SYSFS=y
# CONFIG_OCTEONTX2_AF is not set
CONFIG_OF=y
CONFIG_OF_ADDRESS=y
CONFIG_OF_EARLY_FLATTREE=y
CONFIG_OF_FLATTREE=y
CONFIG_OF_GPIO=y
CONFIG_OF_IRQ=y
CONFIG_OF_KOBJ=y
CONFIG_OF_MDIO=y
CONFIG_OF_NET=y
CONFIG_OLD_SIGSUSPEND3=y
CONFIG_PADATA=y
CONFIG_PARTITION_PERCPU=y
CONFIG_PCI=y
CONFIG_PCIEAER=y
CONFIG_PCIEASPM=y
# CONFIG_PCIEASPM_DEFAULT is not set
CONFIG_PCIEASPM_PERFORMANCE=y
# CONFIG_PCIEASPM_POWERSAVE is not set
# CONFIG_PCIEASPM_POWER_SUPERSAVE is not set
CONFIG_PCIEPORTBUS=y
# CONFIG_PCIE_AL is not set
CONFIG_PCIE_MEDIATEK=y
CONFIG_PCIE_PME=y
CONFIG_PCI_DEBUG=y
CONFIG_PCI_DOMAINS=y
CONFIG_PCI_DOMAINS_GENERIC=y
CONFIG_PCI_MSI=y
CONFIG_PCI_MSI_IRQ_DOMAIN=y
CONFIG_PERF_EVENTS=y
CONFIG_PGTABLE_LEVELS=3
CONFIG_PHYLIB=y
CONFIG_PHYLINK=y
CONFIG_PHYS_ADDR_T_64BIT=y
CONFIG_PHY_MTK_TPHY=y
# CONFIG_PHY_MTK_UFS is not set
# CONFIG_PHY_MTK_XSPHY is not set
CONFIG_PINCTRL=y
# CONFIG_PINCTRL_MT2712 is not set
# CONFIG_PINCTRL_MT6765 is not set
# CONFIG_PINCTRL_MT6797 is not set
CONFIG_PINCTRL_MT7622=y
# CONFIG_PINCTRL_MT8173 is not set
# CONFIG_PINCTRL_MT8183 is not set
CONFIG_PINCTRL_MT8516=y
CONFIG_PINCTRL_MTK=y
CONFIG_PINCTRL_MTK_MOORE=y
CONFIG_PINCTRL_MTK_V2=y
CONFIG_PM=y
CONFIG_PM_CLK=y
CONFIG_PM_GENERIC_DOMAINS=y
CONFIG_PM_GENERIC_DOMAINS_OF=y
CONFIG_PM_OPP=y
CONFIG_POWER_RESET=y
CONFIG_POWER_RESET_SYSCON=y
CONFIG_POWER_SUPPLY=y
CONFIG_PRINTK_TIME=y
CONFIG_PWM=y
CONFIG_PWM_MEDIATEK=y
# CONFIG_PWM_MTK_DISP is not set
CONFIG_PWM_SYSFS=y
CONFIG_QUEUED_RWLOCKS=y
CONFIG_QUEUED_SPINLOCKS=y
CONFIG_RAS=y
CONFIG_RATIONAL=y
# CONFIG_RAVE_SP_CORE is not set
CONFIG_RCU_NEED_SEGCBLIST=y
CONFIG_RCU_STALL_COMMON=y
CONFIG_REALTEK_PHY=y
CONFIG_REGMAP=y
CONFIG_REGMAP_MMIO=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_REGULATOR_MT6380=y
CONFIG_RESET_CONTROLLER=y
CONFIG_RFS_ACCEL=y
CONFIG_RODATA_FULL_DEFAULT_ENABLED=y
CONFIG_RPS=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_DRV_MT7622=y
CONFIG_RTC_I2C_AND_SPI=y
CONFIG_RTL8367S_GSW=y
CONFIG_RWSEM_SPIN_ON_OWNER=y
CONFIG_SATA_HOST=y
CONFIG_SCSI=y
# CONFIG_SECTION_MISMATCH_WARN_ONLY is not set
CONFIG_SERIAL_8250_FSL=y
CONFIG_SERIAL_8250_MT6577=y
CONFIG_SERIAL_8250_NR_UARTS=3
CONFIG_SERIAL_8250_RUNTIME_UARTS=3
CONFIG_SERIAL_DEV_BUS=y
CONFIG_SERIAL_DEV_CTRL_TTYPORT=y
CONFIG_SERIAL_MCTRL_GPIO=y
CONFIG_SERIAL_OF_PLATFORM=y
CONFIG_SGL_ALLOC=y
CONFIG_SG_POOL=y
CONFIG_SMP=y
CONFIG_SPARSEMEM=y
CONFIG_SPARSEMEM_EXTREME=y
CONFIG_SPARSEMEM_MANUAL=y
CONFIG_SPARSEMEM_VMEMMAP=y
CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y
CONFIG_SPARSE_IRQ=y
CONFIG_SPI=y
CONFIG_SPI_MASTER=y
CONFIG_SPI_MEM=y
CONFIG_SPI_MT65XX=y
CONFIG_SPI_MTK_NOR=y
CONFIG_SPI_MTK_SNFI=y
CONFIG_SRCU=y
CONFIG_SWCONFIG=y
CONFIG_SWIOTLB=y
CONFIG_SWPHY=y
CONFIG_SYSCTL_EXCEPTION_TRACE=y
CONFIG_SYSVIPC_COMPAT=y
CONFIG_SYS_SUPPORTS_HUGETLBFS=y
CONFIG_THERMAL=y
CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0
CONFIG_THERMAL_EMULATION=y
CONFIG_THERMAL_GOV_BANG_BANG=y
CONFIG_THERMAL_GOV_FAIR_SHARE=y
CONFIG_THERMAL_GOV_STEP_WISE=y
CONFIG_THERMAL_GOV_USER_SPACE=y
CONFIG_THERMAL_OF=y
CONFIG_THERMAL_WRITABLE_TRIPS=y
CONFIG_THREAD_INFO_IN_TASK=y
CONFIG_TICK_CPU_ACCOUNTING=y
CONFIG_TIMER_OF=y
CONFIG_TIMER_PROBE=y
CONFIG_TREE_RCU=y
CONFIG_TREE_SRCU=y
CONFIG_UBIFS_FS=y
CONFIG_UBIFS_FS_ADVANCED_COMPR=y
CONFIG_UBIFS_FS_LZO=y
CONFIG_UBIFS_FS_ZLIB=y
# CONFIG_UCLAMP_TASK is not set
# CONFIG_UNMAP_KERNEL_AT_EL0 is not set
CONFIG_USB=y
CONFIG_USB_COMMON=y
CONFIG_USB_SUPPORT=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_MTK=y
# CONFIG_USB_XHCI_PLATFORM is not set
CONFIG_VMAP_STACK=y
CONFIG_WATCHDOG_CORE=y
CONFIG_WATCHDOG_PRETIMEOUT_DEFAULT_GOV_PANIC=y
CONFIG_WATCHDOG_PRETIMEOUT_GOV=y
# CONFIG_WATCHDOG_PRETIMEOUT_GOV_NOOP is not set
CONFIG_WATCHDOG_PRETIMEOUT_GOV_PANIC=y
CONFIG_WATCHDOG_PRETIMEOUT_GOV_SEL=m
CONFIG_WATCHDOG_SYSFS=y
CONFIG_XPS=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZONE_DMA32=y